Miche AXY CONNECT Manual De Uso Y Mantenimiento página 5

• Never wash the parts with pressure-fed water, because water
may penetrate the seals and cause permanent damage to the
internal components. We recommend washing the components
using a sponge, mild soap and water.
SECTION II:
Hubs
Warning
If you have any doubt whatsoever your service-repair
ability, please take your bicycle to a qualified repair
shop.
Before any maintenance operations on your wheels,
always wear gloves and protection glasses.
Use original spare parts exclusively provided by Fac
Michelin Spa.
When replacing any broken sealed bearings please ensure sealed
bearing correct measure and specification are used.
Rear Hub Right side
Left side
Free wheel MICHE 24x12x6 (6901)
Front hub
The AXY CONNECT hubs are easy to maintain. To do it, proceed
as follows:
Front hub
Insert two keys (A) in the extremity of the hubs (Pic. 1), and turn
them in anti-clock sense.
While you are taking out the mobile side, take out from the
opposite side the complete pin.
• Once you take out the pin from hub's body, you could, if it is
necessary, change the bearings.
To reassembly it:
• Put the pin into the hub's body and lock with power the mobile
side with a torque of 15 Nm. If necessary, adjust the hub by
working on the ring (D):
• Unlock the grub screw (E) with a key (B) (Pic. 1).
• Turn the ring clockwise to drop the sliding, and anti-clockwise to
raise the sliding. Lock the grub screw (E).
Check the sliding of the wheel.
Please check that the hub is correctly tightened and closed, failure
to do so could lead to a serious or fatal accident.
Warning
Use original spare parts exclusively provided by Fac
Michelin Spa. Any modification or alteration (also
graphic) of the product with non-original spare parts or
spare parts not delivered directly by Fac Michelin Spa,
involves the expiration of the guarantee
Rear hub
Insert two keys (A) in the extremity of the hubs (Pic. 2), and turn
them in clock sense.
• Once you take out the pin from hub's body, the free wheel body
(C) stays attached with his pawls (Pic. 2).
• Clean carefully the pawls then put some low-density grease.
• Re-fit the pin (C) inside hub body with the spacer (Z) (Pic. 2).
• Take care to position of the pawls positions. Lock with power the
mobile side with a torque of 15 Nm, if necessary adjust the hub by
working on the ring (D):
• Unlock the grub screw (E) with a key (B) (Pic. 3).
• Turn the ring in clock sense to drop the sliding, and in anti-clock
sense to rise the sliding. Lock the grub screw (E).
Check the sliding of the wheel.
Please check that the hub is correctly tightened and closed, failure
MICHE 28x12x8 (6001)
MICHE 24x12x6 (6901)
MICHE 24x12x6 (6901)
to do so could lead to a serious or fatal accident.
Warning
Use original spare parts exclusively provided by Fac
Michelin Spa. Any modification or alteration (also
graphic) of the product with non-original spare parts or
spare parts not delivered directly by Fac Michelin Spa,
involves the expiration of the guarantee
SECTION III:
Spokes
The spokes used to assembly the AXY CONNECT Wheels have
the following measure and features:
Rear whee
Right side
Left side
Front wheel
Right side
Left side
CHANGE A SPOKE
Warning
If you have any doubt whatsoever your service-repair
ability, please take your bicycle to a qualified repair
shop.
Before any maintenance operations on your wheels,
always wear gloves and protection glasses.
Use only spokes of the same length and characteristics
of those being replaced.
Use original spare parts exclusively provided by Fac
Michelin Spa.
Front hub
• Insert two keys (A) in the extremity of the hubs. Turn them in anti-
clock sense. (Pic.4)
• Once you take out the mobile side, if it is necessary take out the
complete pin from the opposite side.
Take out the damaged spoke, then put in the new spoke (Pic.4).
• If it is necessary put the pin into hub's body, and lock with power
the mobile side with a torque of 15 Nm. It is possible eventually
adjust the hub, by working on the ring (D), as explained on Section
II: Hubs – Front hub.
Check the sliding of the wheel.
Please check that the hub is correctly tightened and closed, failure
to do so could lead to a serious or fatal accident.
Rear hub
To change a spoke on the left side of the hub:
• Insert two keys (A) inside the extremity of the hub and turn them
in clock sense.
• Once you take out the mobile side, take out the damaged spoke,
then put in the new spoke (Pic.5).
• Lock with power the mobile side with a torque of 15 Nm and,
if it is necessary, adjust the hub by working on the ring (D), as
explained on the Section II: Hubs – Rear Hub.
Check the sliding of the wheel.
Please check that the hub is correctly tightened and closed, failure
to do so could lead to a serious or fatal accident.
To change the spokes on the free wheel side of the hub, it is no
necessary to take out the pin from hub's body.
To ensure the optimum wheel "dish" spoke line, please follow the
indications below:
5
297,5 mm
275,5 mm
275,5 mm
275,5 mm
ENGLISH