Peg-Perego GT3 Instrucciones De Uso página 19

push the front bar into the armrest. (Repeat on the
other side.)
SIDE DRINK HOLDERS
41 The stroller is equipped with two side drink holders
that fold away or pull out as necessary. To pull the drink
holders out, lift the upper part and lower the bottom
part, as shown in the figure.
42 Turn the disk outwards, and place your drink in
the holder. To clos e the drink holder, carry out the
instructions in reverse order.
ADJUSTABLE HANDLEBAR
43 The handlebar on the stroller is height-adjustable. To
adjust the height of the handlebar, simultaneously
press the side buttons as shown in the figure and block
the handlebar in the desired position.
BASKET
44 The basket on the stroller has three positions.
A: Regular position.
B: Lower position allows you to use the basket even
when the backrest is completely lowered. By pressing
on the basket, it is easier to fill it without disturbing the
baby.
C: Raised basket allows the rear footboard to be used.
GANCIOMATIC SYSTEM
The Ganciomatic System is the swift, practical system
that allows one to fasten the following products,
which can be bought separately and are also equipped
with Ganciomatic System, to the stroller, thanks to
Ganciomatic fasteners.
_ Primo Viaggio: a car seat with base, it can be detached
from its base (which stays in the car) and attached to
the Ganciomatic fasteners of the stroller to transport
your child without disturbing him/her.
_ Navetta: the comfortable bassinet unit becomes a
carriage when attached to the fasteners of the stroller.
Equipped with a foldable hood and carrying handle,
both the air circulation regulation system inside
the bassinet and the inclination of the backrest are
adjustable from outside. At home, it rocks like a cradle
and, when the stand is taken away, it becomes a little
bed.
GANCIOMATIC HOOKS ON THE STROLLER
45 To raise the Ganciomatic hooks on the stroller, lift the
sack at the corners of the seat.
46 Raise the two Ganciomatic hooks. They will
automatically move outwards.
_ To lower the hooks, pull them inward and down.
GT3 + PRIMO VIAGGIO
47 To fasten the car seat to the stroller:
- set the brake on the stroller;
- remove the hood from the stroller;
- completely lower the backrest on the stroller;
- raise the Ganciomatic hooks on the stroller;
- place the car seat, turned towards the adult, on the
stroller and push downward until it clicks into place.
- Do not remove the front bar of the stroller when
attaching the car seat, and make sure that it is in its
original position.
_ See the user's manual for instructions on how to
detach the car seat from the stroller.
GT3 + NAVETTA
48 To fasten the Navetta bassinet unit to the stroller, you
must:
- put the brakes on the stroller;
- remove the hood from the stroller;
- lower the backrest of the stroller completely;
- raise the Ganciomatic fasteners on the stroller;
- remove the front bar;
- raise the footrest on the stroller to the highest possible
position;
- hold onto the handle of the Navetta;
- position the Navetta on the Ganciomatic fasteners of
the the stroller, keeping the head end of the bassinet at
the end of the stroller opposite the handlebar;
- press down with both hands on the sides of the
Navetta until you hear a click.
_ To unfasten the Navetta bassinet unit from the stroller,
consult its instruction manual.
REMOVING THE WHEELS
49 To remove the rear wheels, press the button as shown
in the figure and pull the wheels off the sides of the
stroller.
50 To remove the front wheel, press the button under the
footboard and pull the wheel off.
FOLDING UP THE STROLLER
Before folding the stroller up, set the front wheels to
stationary. If the hood is mounted, lower the braces.
51 To fold the stroller up, press button number 1 (A) using
your right hand.
52 Using your left hand, grab the handle as shown in the
figure. Press button number 2 (B) and lift the handle (C)
to the top notch.
53 After folding the stroller, fasten the safety hook as
shown in the figure.
REMOVABLE LINING
54 To remove the lining from the stroller, unbutton the
sack from the seat and slip it off the footboard, as
shown in the figure.
55 Detach the sack from the armrests, as shown by the
arrows in the figure.
56 Pull the safety belt leg divider up from under the seat.
Unbutton the side tabs from the backrest.
57 Slip the tabs off the backrest as shown in the
figure. Remove the sack and wash it, following the
instructions printed here.
GT3 Naked Chassis
To convert GT3 into a chassis:
58 Place the backrest in the second position and remove
both the side pieces that support the backrest.
59 Press both buttons at the bottom of the backrest
(Fig. A) while lifting the backrest as shown in figure B.
Before fastening the Navetta bassinet unit or the Primo
Viaggio car seat to the chassis, pull the rear part of the
Ganciomatic base upwards as shown in figure C.
_ To turn the chassis back into a stroller, repeat the
instructions above in reverse order.
THE GANCIOMATIC SYSTEM with GT3 NAKED CHASSIS
The Ganciomatic system is a practical, fast way
to fasten the Navetta bassinet unit and the Primo
Viaggio car seat – which are both equipped with the
Ganciomatic system - to the GT3 Naked chassis, using
the Ganciomatic hooks.
GANCIOMATIC HOOKS ON THE CHASSIS
_ To raise the Ganciomatic hooks on the chassis, turn
them upwards until they click into place, as shown in
the figure.
_ To lower the fasteners, turn them the opposite
direction.
GT3 Naked + NAVETTA
60 To fasten the Navetta bassinet unit to the GT3 Naked
chassis:
- Set the brake on the GT3 Naked chassis.
- Raise the Ganciomatic fasteners.
- Pull the footboard upwards to the top position.