Tabla de contenido
Idiomas disponibles
Idiomas disponibles
1. Intended use of the product
This product serves exclusively to accelerate the dry- ing/
curing of putty, filler, base and clear coats. This applies
to both water-borne and solvent-based products. It´s site
of use is the preparation area and finishing area. Within
the automotive industry and vehicle repair sectors, it is
used to cure small areas before polishing. The product
must not be used for other purposes than the described
drying processes.
The maximum ambient temperature during operation
should not exceed 40°C. The device IRT 464 DTP must
not be used in spray booths or within 5 meters of spray
processes to avoid explosion.
2. Product description
The dryer is an essential aid for paint repair on small
and medium sized areas.
The easily manoeuvrable IRT 464 DTP is equipped with
one or two compact cassettes. Each cassette is equipped
with six Infrared (IR) lamps with gold plated reflectors
and a ventilator. The design, combined with a gas spring,
makes positioning of the cassette simple. The IR lamps
are easily exchangeable and the reflectors are protected
against mechanical damage with a mesh. The dryer has a
selection of sophisticated programs.
2.1 Particular advantages
2.1.1 Higher quality
Using the dryer when you cure putty also improves the
quality of the top coat.
The short wave IR curing enables the coating to be cured
from the inside and outwards. This prevents solvents to
be trapped inside the coating and secures a fast and
high quality curing.
2.1.2 Short drying times
60 cm distance
MATERIAL
Putty
Filler Bright
Filler Dark
Water base
Base coat
Top coat
Clear coat
Filler on plastics
Top coat on plastics
Clear coat on plastics
Final boost
Soft cure
2.1.3 Regulated temperature
The dryer has a pyrometer which carefully controls
object temperature. The computer does not only
measure the maximum allowed temperature but also
controls the rate of temperature raise. It ensures that the
701012 rev 9
MINUTES
5-6
10-15
10-15
4-6
4-8
10-15
10-15
10-15
13-17
13-17
2-4
13-17
programmed drying/curing temperature is maintained,
thereby achieving optimum curing, without risk for "over
burning".
2.1.4 Hi tech shape of reflectors with short wave IR
By using short-wave technology and gold-coated
reflectors with a high tech shape important advantages
are achieved. Firstly, by radiating only the needed areas
and not heating any air, a lower energy consumption is
achieved. Secondly, a more uniform surface temperature
is obtained by distributing the energy evenly. Thirdly, a
larger drying surface is achieved. Fourthly, less radiation
outside the curing area.
2.2 Technical data
All dryers emit short wave radiation with a peak at 1120 nm.
The pictures below show the maximum drying area, when
the respective dryer is used in 60 cm distance from a black
sheet metal. For 424, 425 and 428 DTP refer to Manual:
701014 IRT 42x DTP Assembly and Complementary
Instruction to 701012.
IRT 464 DTP 4-1 PcAuto drying surface
0,6 m
Voltage
380 – 420 V
3~ PE
Frequency
50 – 60 Hz
Current
9 A
14 A
Power
6 kW
10 kW
Fuse**
10 A*
16 A*
Drying temp.
Max. 170
o
Noise level
<70 dB(A)
IRT 464 DTP 4-2 PcAuto IRT 464 DTP 4-20 PcAuto drying
surface
1,2 m
Voltage
380 – 420 V
3~ PE
Frequency
50 – 60 Hz
Current
4 – 2 PcA
16 A
29 A
4 – 20 PcA
17 A
29 A
Power
12 kW 20 kW
Fuse**
4 – 2 PcA
16 A*
32 A*
4 – 20 PcA
Max.
Max.
100 A
100 A
Drying temp.
Max. 170
Noise level
<70 dB(A)
* MCB (Minature Circuit Breaker) type C or D.
Fuse type slow-blow.
** The dryer must be operated with the recommended fuse rating.
Weight, dimensions and product identity label on last page.
GB
440 – 480 V
230 V
2~ PE
3~ PE
2~ PE
50 – 60 Hz
50 – 60 Hz
13 A
9 A
26 A
6 kW
6 kW
6 kW
16 A*
10 A*
30 A*
30 A*
Max. 170
o
Max. 170
<70 dB(A)
<70 dB(A)
440 – 480 V
230 V
2~ PE
3~ PE
1~ PE
50 – 60 Hz
50 – 60 Hz
26 A
16 A
48 A
26 A
16 A
-
12 kW
12 kW
12 kW
12 kW
30 A*
16 A*
-
30 A*
30 A*
16 A*
-
30 A*
Max. 170
Max. 170
o
o
<70 dB(A)
<70 dB(A)
3~ PE
15 A
6 kW
o
3~ PE
30 A
30 A
o
*
3
Tabla de contenido
