Connecting Analogue Equipment; Placement Of Transmitter And Headphones - Panasonic RP-WF6000 Instrucciones De Funcionamiento

Connections
Using an optical digital cable
● Do not let falling objects subject the optical digital cable to vibration or
shock.
● Hold the plugs in your hands and carefully connect or disconnect the
optical digital cable.
● If the ends of the optical digital cable become dirty or dusty, efficiency will
decrease. Keep them clean.
● For safety reasons, attach plug caps and do not bend the optical digital
cable too much.
Playing DTS signals
Select the DTS audio signal on the connected equipment.
● A DTS compatible DVD player is necessary to play DVD discs recorded in DTS. (Refer to your DVD player's
operating instructions for further details.)
● If "OFF" has been selected for the DVD player's DTS digital setting, sound may not be output even when DTS
output is selected in the DVD menu.
● When connecting a DVD player and this unit with an analogue connection, sound may not be output. Change
to a digital connection if this happens.
● There may be some noise emitted during functions such as rewinding and fast forwarding with a DTS format
DVD. This does not indicate a problem with the unit.

Connecting analogue equipment

Use an audio cable when connecting the AUDIO OUT terminals of a video cassette player, television etc. to the
transmitter's LINE IN (L/R) terminal.
Transmitter
To LINE IN
Audio cable (not included)
terminal
AUDIO-L
(L, white)
AUDIO-R
(R, red) Audio cable (mini pin plug)
(not included)
Audio cable (mini pin plug) (not included)
Use the audio cable (stereo mini plug to 2-pin plug) or similar to connect the transmitter's LINE IN terminal to a
stereo mini headphone jack on the television or portable AV equipment. If the output level from the television
or portable AV equipment is set to low, there may be unwanted noise. Set the volume so the sound is not
distorted.
12
12
The optical digital cable's
minimum bending radius is 25
mm.
To the AUDIO OUT Video cassette
terminals player
AUDIO-L
(L, white)
Television
AUDIO-R
(R, red)
Portable AV
equipment
Headphone terminal etc.
ATT Control
When the sound is low with an analogue connection, switch the ATT (attenuator) control on the Transmitter's
rear panel to [0 dB].
Position
0 dB
-8 dB
Note
–8dB 0dB ● Reduce the volume before switching the ATT control.
ATT ● If the analogue sound input is distorted (there may also be noise), switch
the ATT control to [-8 dB].

Placement of transmitter and headphones

This unit uses radio waves to transmit the signals so use the headphones within the range of the radio waves.
The range of the radio waves
The radio waves have a maximum range of 30 m from the transmitter.
The most appropriate frequency is automatically set when the headphones are taken off the transmitter. When
the headphones are used outside the range of the radio waves or the radio waves weaken, the sound is
broken. Move nearer to the transmitter or reset the frequency (
frequency]).
● Since this unit is using the 2.4 GHz radio frequency band, obstacles (such as reinforced concrete walls
and metal doors) may cause the sound to be broken. This is a characteristic of radio waves and not a
malfunction.
● The sound heard from the headphones will differ depending on where the transmitter is placed and the kind
of location in which it is used. We recommend placing the transmitter where the sound is received best.
● The sound may be broken when the unit is used at the same time as other equipment that uses the 2.4 GHz
radio frequency band such as wireless equipment or microwaves.
Locations
Avoid placing the unit in the following locations
- Places with high temperatures such as near heating appliances or places directly exposed to sunlight
- Places with a lot of dust
- On top of unstable carts or inclined surfaces
- Places with excessive vibration
- Bathrooms and other moisture-prone places
Source
Equipment with a low output level such as televisions and
portable equipment
Other equipment (setting at shipment)
page 16 [Setting the most appropriate
13
13