Panasonic RP-WF6000 Instrucciones De Funcionamiento página 10

Troubleshooting guide
Problem Possible cause and suggested remedy
Sound is low. y If analogue input is selected, switch the transmitter's ATT control to "0 dB"
( page 13).
y If the transmitter is connected to the headphone jack, turn up the volume on the
connected equipment (
y Turn up the volume on the headphones (
Sound is distorted. y If analogue input is selected, switch the transmitter's ATT control to "-8 dB"
( page 13).
y If the transmitter is connected to the headphone jack, turn the volume down on the
connected equipment
( page 12).
y Set "CINEMA", "MUSIC" or "VOICE" with the SURROUND button on the transmitter
when playing a DTS source.
Sound is broken y Change the placement of the transmitter. Stay within the range of the transmitter
(noise may be ( page 13).
heard too).
y The headphones' OPR lamp dims. Sound is distorted, intermittent or there is
excessive background noise during use (
● The rechargeable battery has run down. Recharge it or replace the alkaline dry cell
batteries with new ones.
y Make sure that there is no other equipment that uses the 2.4 GHz radio frequency
band such as wireless equipment or microwaves near the transmitter or headphones
( page 5).
y Set the most appropriate frequency (
frequency]).
There is excessive y If the transmitter is connected to the headphone jack, turn the volume up on the
background noise. connected equipment (
y The headphones' OPR lamp dims. Sound is distorted, intermittent or there is
excessive background noise during use. (
● The rechargeable battery has run down. Recharge it or replace the alkaline dry cell
batteries with new ones.
y Make sure that there is no other equipment that uses the 2.4 GHz radio frequency
band such as wireless equipment or microwaves near the transmitter or headphones
( page 5).
y Set the most appropriate frequency (
frequency]).
Audio cannot
y When the input audio (analogue only) continues to be very low for more than 5
be heard while minutes (approximately), the radio waves being emitted from the transmitter may
analogue is stop ( page 15).
selected. In this case perform the following steps.
1. Switch the ATT control on the transmitter to "0 dB" (
If audio still cannot be heard
2. Increase the volume level on the equipment connected to the analogue input
and decrease the volume level on the headphones.
18
18
page 12).
page 14).
page 10).
page 16 [Setting the most appropriate
page 12).
page 10).
page 16 [Setting the most appropriate
page 13).
Problem Possible cause and suggested remedy
No surround effect. y Set "CINEMA", "MUSIC" or "VOICE" on the transmitter's SURROUND button
( page 16).
y The input audio signal is not multi-channel. There is no surround effect when playing
a monaural source (
The DOLBY y You have selected "PCM" for the audio digital output setting on the DVD player
(includes game machines).
DIGITAL lamp
● Select "Dolby Digital/PCM" or "Dolby Digital" if the DVD player has an internal
does not light.
Dolby Digital decoder.
y You are playing a signal that is not recorded in DOLBY DIGITAL format.
y The chapter being played is not DOLBY DIGITAL format.
The DOLBY PRO
y You have set the transmitter's SURROUND button to "OFF" (
LOGIC II lamp
y There are no analogue input signals, digital input signals (PCM), Dolby Digital 2-
does not light.
channel signals or MPEG-2 AAC 2 channel signals being input.
The DOLBY PRO y You have set the transmitter's SURROUND button to a setting other than "OFF"
( page 15).
LOGIC II lamp
lights.
y There are analogue input signals, digital input signals (PCM), Dolby Digital 2-channel
signals or MPEG-2 AAC 2 channel signals being input.
The DTS lamp y You have selected "OFF" for the DVD player's DTS digital output setting
( page 12).
does not light.
● Refer to the operating instructions for the DVD player and set the DTS digital
output setting on the DVD player to "ON".
y You are playing a signal that is not recorded in DTS format.
y The chapter being played is not DTS format.
y The DVD player is not DTS compatible (
● Use a DTS compatible DVD player.
The MPEG-2 AAC y The television's output setting is set to "PCM".
lamp does not
● Refer to the operating instructions for the television and set the television to output
light. MPEG-2 AAC signals.
Cannot select dual y Connect the analogue audio output of the equipment to the LINE IN terminal and
audio (MAIN/SUB)
select the desired sound on the connected equipment (
when input is
digital.
Cannot charge.
y The OPR/CHARGE lamp on the transmitter does not glow red (
● Check that the headphones are put on the transmitter correctly.
y A dry cell battery is inserted.
● Be sure to insert the supplied nickel-metal hydride rechargeable battery.
y A nickel-metal hydride rechargeable battery other than the supplied one is inserted.
● Insert the supplied nickel-metal hydride rechargeable battery or a dedicated
replacement battery RP-BP6000 (optional). (
y There is dirt on the charging terminals of the headphones or the transmitter
( page 10).
● Remove it gently with a cotton bud etc.
Radio wave output y A noise signal is being received from the connected equipment.
● Turn off the power on the connected equipment.
does not stop.
page 16).
page 15).
page 12).
page 14).
page 9).
page 8)
19
19