Tabla de contenido
Idiomas disponibles
Idiomas disponibles
30.
AUX1-3 Controls - Adjusts the amount of the signal sent from the
ST SUB IN1-3 jacks to the AUX 1, 2 and 3 buses.
31.
ST (stereo) Controls - Adjusts the amount of stereo signal sent
from the ST SUB IN1-3 jacks to the STEREO bus.
32.
PFL (pre-fader listen) Switch - When this switch is engaged, the
signal at the point before the ST control knob is sent to the
PHONES jack.
33.
POWER LED - The LED indicates when the power is switched
on.
34.
PHONES Control - Controls the signal sent to the Headphone
Output.
35.
LPF (MONO OUT) - This switch applies a low-pass filter to the
signal that is output from the STEREO bus. You can adjust the
frequency to the desired position by using a screwdriver to turn
the LPF Control.
36.
ST (stereo) Control - Adjusts the level of the signal sent from the
2TR IN jacks to the STEREO bus.
37.
PFL (Pre-fader listen) Switch - When this switch is engaged, the
signal input from the 2TR IN jacks is routed at the point before the
ST control to the PHONES jack.
38.
AFL Switch - When this switch is on, the output
signal that passes through the ST OUT control fader
is sent to the PHONES jack.
39.
PFL Switch - When this switch is engaged, the signal
at the point before the ST OUT control fader is sent to
the PHONE jack.
40.
DFX RTN Fader - Adjusts the level of the return
signal which is sent from the built-in DSP to the
STEREO bus.
41.
AUX1-3 Fader - The AUX1-3 faders adjust the final
level of the signal sent from the AUX1-3 bus to the
AUX SEND1-3 jacks.
42.
MONO OUT Fader - Adjusts the final level of the
signal output from the STEREO bus to the MONO
OUT jack.
43.
ST OUT Fader - The ST OUT fader adjusts the final
level of the signal sent from the STEREO bus to the
ST OUT jacks.
GRAPHIC EQ
44.
EQ SWITCH - Engage this button to add the stereo graphic
EQ into the main mix output.
45.
STEREO GRAPHIC EQ - Boosts or attenuates (+/-15dB) the
selected frequency at a preset bandwidth.
POWER AMP
46.
POWER AMP. MODE Switch - Provides three modes: MAIN L / MAIN R;
AUX1/MONO; BRIDGE. Select any one of these modes to specify the signals to be
routed to the corresponding jacks according to the speaker connection on the rear
panel.
47.
POWER AMP Switch - This switch is used to control the amplifier input signal.
30
31
32
PFL
ST SUB IN 1
ST SUB IN 2
PFL
AFL
dB
dB
dB
10
10
10
5
5
5
0
0
0
-5
-5
-5
-10
-10
-10
-20
-20
-20
-25
-25
-25
-30
-30
-30
-40
-40
-40
-60
-60
-60
-
-
-
DFX RTN
AUX 1
40
44
EQ OFF
EQ ON
5
1
POWER
2
PHONES
3
OFF
LPF(MONO OUT)
MONO OUT
ST
37
PFL
ST SUB IN 1
AFL
PFL
PFL
PFL
ST SUB IN 3
2TR IN
AFL
AFL
AFL
dB
dB
dB
10
10
10
5
5
5
0
0
0
-5
-5
-5
-10
-10
-10
-20
-20
-20
-25
-25
-25
-30
-30
-30
-40
-40
-40
-60
-60
-60
-
-
-
AUX 2
AUX 3
MONO
STEREO
OUT
42 43
41
63
125
250
500
1K
2K
4K
+15
+10
+5
0
-5
-10
-15
45
MAIN L
AUX 1
A
BRIDGE
46
AMP MODE
ON
OFF
POWER AMP
33
34
ON
35
36
ST
PFL
39
PFL
38
AFL
OUT
8K
16K
+15
+10
+5
0
-5
-10
-15
MAIN R
MONO
B
47
Tabla de contenido
