Tabla de contenido
Idiomas disponibles
Idiomas disponibles
4.
Attach the floor head connector to the extension tubes. [4]
5.
Ensure the handle safety latch is locked. [5]
note: To remove the extension tubes from the handle or the floor head from the tubes,
press the release latch and pull apart.
usinG your cleaner
Before you BeGin cleaninG
Remove the clean water tank cap by pushing down and turning anti clockwise. [6]
1.
2.
Fill the measuring jug no more than the max. fill line.
3.
Insert the funnel into the water tank and fill the unit with water. [7]
4.
Replace the cap by pushing down and turning clockwise.
Ensure the handle safety latch is locked. [5]
5.
imPortant: always unplug the cleaner and press the steam release trigger to
release any remaining steam pressure before adding water.
steam cleaninG hard floors
imPortant: always unplug the cleaner and press the steam release trigger to
release any remaining steam pressure before adding water or changing a textile
pad or accessory tool.
1.
Ensure the floor head is connected to the extension tube.
2.
Place the floor head onto the floor cloth. Lift the levers on either side of the floor
head to secure each end of the floor cloth in place. [12]
3.
Plug the steam cleaner into the main power and switch on. The red ON light will
illuminate. [8]
4.
After a few minutes the green steam ready light will illuminate indicating the cleaner
is ready for use. [8]
Release the steam handle safety latch. [9]
5.
6.
To produce steam press the steam trigger button. [10]
7.
If necessary adjust the variable steam dial to adjust pressure. [11]
8.
move the cleaner slowly backwards and forwards paying particular attention to high
traffic areas.
9.
Remove the floor cloth from floor head and use brush for stubborn dirt.
refreshinG carPets
1.
Repeat steam cleaning hard floors operated steps 2-8 as detailed above.
accessories
All accessories can fit onto the concentration nozzle which can be attached to the hose
handle or the end of the tube .
1.
Ensure the handle safety latch is locked. [5]
2.
To attach the concentration nozzle push onto the handle/extension tube until it
clicks in place. [13]
3.
Push the desired small tool onto the concentration tool aligning the arrows. [14]
4.
Twist clockwise to secure in place. [14]
5.
Plug the steam cleaner into the main power. The red ON light will illuminate. [8]
6.
After a few minutes the green Steam Ready light will illuminate indicating the cleaner
is ready for use. [8]
7.
Release the steam handle safety latch. [9]
8.
To produce steam press the Steam Trigger Button. [10]
9.
If necessary adjust the variable steam dial to adjust pressure. [11]
note: The concentration tool must be attached before fitting any other small tools.
concentration nozzle
Use on heavily soiled areas such as showers, kitchens. [15]
window tool
Use on windows and mirrors for a smear free clean. [16]
upholstery tool
Use the upholstery cloth over the window tool for use on sofas
and chair fabrics. [17]
Plastic Brushes
Use on stubborn grease and grime. [18]
metal Brush
For oven grills and racks. [19]
angled nozzle
For hard to reach areas such as taps etc. [20]
scraper tool
Ideal for dried residue in ovens or defrosting freezers. [21]
imPortant: always unplug the cleaner when adding water, changing a textile pad
or accessory tool.
cleaner maintenance
imPortant: always ensure the cleaner has fully cooled down before performing
any maintenance tasks.
empty the water tank
1.
Unplug the cleaner from the main power and ensure the unit has cooled.
2.
Hold the steam trigger down to release any remaining steam pressure. [10]
3.
Put the steam handle safety latch on. [5]
Remove the clean water tank cap [6] , lift the cleaner and empty any remaining water [22].
4.
Lift the cleaner and empty any remaining water. [22]
5.
2
GB
Tabla de contenido
