Safety Instructions - ANSMANN Energy XC3000 Instrucciones De Uso

EnErgy xc 3000
GB
OPErATIng InSTrUcTIOnS
FOrEWOrD
Dear Customer,
Thank you for deciding to buy the ANSMANN Energy XC3000
charger. These operating instructions will help you to use all
features of your Energy XC3000 charger in an optimum way.
Please read the operating instructions carefully before use. We
hope you are happy with your new charger.
Your ANSMANN Team
IncLUDED In SET
> Charger Energy XC3000
> Power supply
> Mains lead
> Universal adapter plate for connecting Li-Ion/Li-Po batteries
> Operating instructions

SAFETy InSTrUcTIOnS

> Please read the operating instructions carefully before
using the charger!
> Do not use the device if there are signs of any damage to
the housing, mains plug or cable. Please contact an
authorised dealer!
> For charging of round cells and 9V batteries use only with
NiCd/NiMH cells. Other types could cause an explosion!
Observe polarity (+/-) prior to use!
> For charging of Li-Ion/Li-Po batteries the universal adapter
plate provided must be used!
> Please note that due to the high charging current, use
only good quality batteries from a well known brand in this
charger. Using inferior quality batteries could cause
damage to the batteries themselves, and/or the charger,
if they are not suitable for fast charging. If unsuitable
cells are inserted in the charger, warranty claims cannot be
accepted and the warranty will become void!
> Keep the charger in a dry place!
> In order to avoid the risk of fire and/or electric shock, the
charger must be protected against high humidity and water!
> Before cleaning the unit, disconnect it from the mains and
only use a dry cloth!
> Never attempt to open the charger!
> Keep away from children's reach!
> Do not leave the device unattended when in operation!
> Disconnect device from mains supply after use!
> If the safety instructions are not followed, it may lead to
damage to the device or battery and could cause injury!
> We recommend the use of ANSMANN rechargeable batteries!
FUncTIOnAL OVErVIEW OF cHArgEr
> Desktop charger for 1-8 AAA or AA cells; for 1-4 C or D cells in
addition to 1-2pcs 9V E-Block or 1 Li-Ion/Li-Po battery pack
(3.6/3.7V-7.2/7.4V) connected by the universal adapter plate
provided.
> Suitable for NiCd, NiMH, Li-Ion/Li-Po batteries
> Multifunctional clear LCD display
> Adjustable charging current (2 steps) for all round cells
> Automatic charging current adjustment
> Charge condition is irrelevant before charging
> Capacity quick test of the inserted cells
> Individually selectable charging programs per charging slot
• CHARGE
• DISCHARGE
• BATTERY-TEST (charging, discharging, charging)
• CYCLE (1-10 cycles discharging/charging adjustable)
> Automatic start of charging within 10 seconds after contact
with the battery if no charging program is selected.
> The selected charging program is displayed on the LCD display
> Microprocessor controlled charging and supervision of each cell
> Individual monitoring of critical parameters during charging
• VOLTAGE (charge/discharge voltage)
• CURRENT (charge/discharge current)
• CAPACITY (charge/discharge capacity)
• TIME (charge/discharge time)
> Multiple over charging protection
> Trickle charging for NiCd/NiMH batteries
> Faulty cell detection and Alkaline detection
> Wrong polarity protection
> Switch mode power supply for world wide use
(100-240V AC / 50-60Hz)
FUncTIOnAL OVErVIEW BATTEry TESTEr
> Reliable tester for all common batteries
> Ultra fast testing result
> Indication of the battery voltage and capacity
(in 10% steps) by the LCD display
The following cells can be tested:
> 1.5V Alkaline cylindrical cells & 1.2V NiCd/NiMH batteries:
AAA, AA, C, and D cells
> 9V E-block / 12V A23
> 1.5V Alkaline button cells: LR43, LR44, LR45, LR48, LR54,
LR55, LR57, LR58, LR59, LR60, LR66
> 1,44V Zinc-Air button cells: V13, V675, V312
> 3V Lithium button cells: CR1025, CR1216, CR1220, CR1616,
CR1620, CR2016, CR2025, CR2032, CR2320, CR2430, CR2450
> Lithium photo batteries: 3V: CR2, CR123A, CR-V3 / 6V: CR-P2, 2CR5