Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Average air consumption free speed
Average air consumption at load
Air intlet size
Recommended hose size
Maximum air pressure
Noise values and vibration values (triax vector sum) according to
EN ISO 11148-6:
L
(emission sound pressure level)
PA
L
(sound power level)
WA
K (uncertainty for the given sound level)
Vibration emission value a
=
h
Uncertainty K =
Work Stations
Your air ratchet should only be used as a hand operated
tool. It is always recommended that the tool is used when
standing with solid footing. It can be used in other positions
but before any such use, the operator must be in a secure
position having a firm grip and footing and be aware that
when loosening fasteners the tool can move quite quickly
away from the fastener being undone. An allowance must
always be made for this rearward movement so as to avoid
the possibility of hand/arm/body entrapment.
Features
Forward/Reverse Switch (Fig. A)
The forward/reverse switch
5
forward or reverse direction for easier and robust operation.
3/8" and 1/2" Square Drive (Fig. A)
The 3/8" and 1/2" square drive
3/8" and 1/2" drive sockets.
Sealed Head (Fig. A)
The sealed head
6
design prevents yoke spread under
heavy torque application.
Rubber Grip Handle (Fig. A)
This air tool has a rubber grip handle
thermoplastic elastomer (TPE) designed for improved
comfort, slippage reduction, and better tool control.
Variable Speed Trigger (Fig. A)
The variable speed trigger
2
the start and stop of the air tool.
1/4" Inlet (Fig. B)
The tool's 1/4" inlet
3
located at the bottom of the handle
is used for connecting an air supply with a standard 1/4"
NPT American thread.
MPF59038
35 SCFM (17 L/s)
4.9 CFM (2.3 L/s)
35 SCFM (17 L/s)
4.9 CFM (2.3 L/s)
1/4" NPT(F)
3/8" (10 mm)
90 PSI (6.2 Bar)
91
dB(A)
102
dB(A)
3
dB(A)
3.0
m/s
2
m/s
2
1.5
allows the tool to operate in a
1
allows the attachment of
4
made of molded
allows the operator to control
Fig. B
Torque Assist™ Clutch (Fig. C)
The integrated Torque Assist™ clutch
give the user control by limiting torque as needed. This
can prevent damaging fasteners and reduce kickback in
tightening applications. The Torque Assist™ clutch features
two settings and a max setting to deliver full power.
Fig. C
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove air supply before
making any adjustments or removing/installing
attachments or accessories. An accidental start‑up
can cause injury.
Attaching and Removing Square Drive
Anvils (Fig. A)
Your tool is supplied with two anvils, a 3/8" square drive
anvil
8
and a 1/2" square drive anvil
with the corresponding sized sockets. To install an anvil just
push it into the square drive
anvil can be installed on the front or back of the head in
order to enable you to more versatility to get the tool into
tight spaces more comfortably.
To remove the anvil from the air ratchet, push the button on
the back of the anvil and slide the unit out.
Air Supply (Fig. D)
The recommended hook-up is shown in Figure D.
Pneumatic tools operate on a wide range of air pressures.
For maximum efficiency and longer tool life, the pressure of
the air supplied to these tools MUST not exceed the rated
PSI at the tool when the tool is running. Using a higher than
rated pressure will cause faster wear and drastically shorten
English
3
7
is designed to
7
9
, suitable for use
until you hear a "click". The
1
5
Tabla de contenido
