Gaggenau BS 27 Serie Instrucciones De Montaje página 7

Zuerst den Dampfbackofen, anschließend den Backofen
montieren.
Bei Einbau neben einem Backofen müssen sich die Griffe
der beiden Geräte in der Mitte befinden.
Kombination mit Wärmeschublade
WS 2..
Zuerst die Wärmeschublade montieren. Montageanleitung
der Wärmeschublade beachten.
Den Zu- und Abwasser schlauch des Dampfback ofens
hinten im Einbau schrank nach unten zu den Anschlüssen
führen. Den Dampfbackofen auf die Wärmeschublade in
den Einbauschrank einschieben.
Wichtig: Beim Einschieben die Blende und den Griff der
Wärmeschublade nicht beschädigen.
Ausbau
Gerät spannungslos machen. Befestigungsschrauben
lösen.
Gerät leicht anheben und ganz herausziehen.
en
$
Important Notes
The appliance is only guaranteed safe to use if installed by
a specialist in accordance with these installation
instructions.
The installer is liable for any damage resulting from
incorrect installation.
The appliance may only be connected by a licensed
specialist. The local electricity supplier's regulations and
construction regulations apply.
Do not install another electrical appliance above this
appliance in the cabinet.
Dispose of the packaging according to local regulations.
Check the appliance for any transport damage.
The appliance must be disconnected from the electricity
before any installation work takes place.
Accessories for installation
You can order the following accessories for installation:
GZ 010-011: Extension for inlet and outlet (length 2 m).
WF 040-020: Brita descaling system (filter head with non-
return valve and filter cartridge) for first installation
If the hardness of the water exceeds 9° (English water
hardness), you must install a descaling system between
the tap and the appliance to reduce the build-up of
limescale.
Preparing the Cabinet – Figure 1a /1b
1 – cold water connection
2 – water drain
3 – descaling system
Fitted units must be heat-resistant up to 90 °C, adjacent
unit fronts up to at least 70 °C.
Secure furniture which is not fitted to the wall using a
standard fixture.
Install the appliance low enough to allow trays to be easily
removed.
Electrical Connection
Observe rating plate data for voltage and total rating.
Important: only connect in accordance with the
connection diagram. Fit the enclosed copper bridges as
required.
Mains connection lead: Type H05 VV-F or higher. The
yellow-green lead for the earth connection must be 10 mm
longer on the appliance side than the other leads.
Do not trap the lead during installation and do not guide it
over sharp edges.
The appliance corresponds to safety class I and may only
be used in conjunction with a safety earth terminal. Fuse
protection using B or C circuit breakers is required.
An all pin isolating switch with a contact gap of at least
3 mm must be installed.
Shock protection must be guaranteed by the installation.
Water Connection – Figure 2
4 – electrical connection
5 – cold water connection
6 – water drain
Only connect the appliance to a cold water connection
(water pressure 2 - 10 bar) with a R 3/4˝ hose connector.
The water connection must always be accessible, and
must not be directly behind the appliance.
If the hardness of the water exceeds 9° (English water
hardness), you must install a descaling system between
the tap and the appliance. We recommend the Brita
descaling system WF 040-020 which you can order from
your kitchen specialist.
Fit the elbow connector to the appliance. Fit the enclosed
seals.
Run the water for a few minutes if the water pipe is new or
if it has not been in use for a prolonged period of time
without the appliance being connected to the water mains.
Otherwise, the water supply line may clog up and the
appliance will signal that the water is low.
The steam oven is protected against back-suction
(DVGW-tested). There is therefore no need to install
connection fittings with non-return valve. Special local
waterworks regulations must be observed very precisely.
7