Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Prepare built-in units
Important:
The power outlet must be located outside the
built-in cut-out.
Make sure there is adequate air circulation. To do this,
remove the rear panel of the cabinet or cut out an
opening of 19
⁄
" x 15
⁄
11
3
16
be a gap of at least 1
3
⁄
" (35 mm) between the wall and
8
base of the unit or the rear panel of the unit situated
above. The ventilation slots and intake openings must
not be covered. Also follow the installation instructions
for the appliance situated above or below. If installing
the appliance above a warming drawer, the height of the
recess must be 23
1
⁄
" (590 mm). If the appliance is
4
installed directly under a décor panel, ensure that there
is a ventilation slot of at least 31 square inches
(200 cm
). The ideal installation height for the fully
2
automatic espresso machine, measured from the floor to
the lower edge of the appliance, is 37
Protect your Coffeemaker and hoses against freezing or
it will be damaged.
9
CAUTION
Installation must always be performed by two
persons.
" (500 x 400 mm). There must
4
⁄
" (950 mm).
3
8
Installation preparation
1
Unpack all the parts and check for any damage in
transit. Do not operate a damaged appliance.
2
Take note of the installation dimensions of the
particular model.
Fig. 2
Two opening angles can be selected for
Important:
the door. Depending on the opening angle
required, the mounting distance to the wall should
be observed before installation.
‒ Opening angle approx. 110° (delivery status)
= mounting distance to the wall at least 13
(350 mm).
‒ Opening angle approx. 155°
= mounting distance to the wall at least 25
(650 mm).
For an opening angle of 155°, remove both the
restrictors at the top and bottom of the hinge.
3
Position the assembly bracket
measurement stated in the image and fasten it with
2 fastening screws
(f)
The assembly bracket must be positioned at the
base of the unit and the wall such that no gap is
present.
Fig. 3
4
Fasten the transformer mount
(f)
in the middle.
Fig. 4
5
Insert the transformer in the mount. The connec-
tions to both lines must point to the left.
Note: When positioning the transformer
pushing in the appliance, do not trap the lines.
The transformer
(k)
appliance and the back wall of the cupboard.
6
Set the main switch
(U)
Important: Fig. 7
‒ The distance between the appliance and the rear
wall must be at least 13
‒ A recess of 4
⁄
23
32
required for water inlet hose and drain water
hose. If required, adjust the furniture base
accordingly.
‒ The hose guide
(l)
furniture base.
‒ The connecting hose guide
adapted to the edge of the furniture if necessary.
7
Screw the hose guide
to the rear wall of the appliance.
(i)
8
Insert the drain water hose in the hose guide
9
Place the hose straight on the bottom of the
furniture and run down over the edge.
10 Run the connecting cable, the water inlet hose and
the drain water hose through the cabinet to the
back.
NOTICE: The connecting cable and hoses should
not be kinked, crushed or twisted
(c)
according to the
to the cabinet as shown.
with 2 screws
(d)
Fig. 5
(k)
is not allowed to touch the
Û
to [
] on the appliance.
⁄
" (100 mm).
15
16
" (120 mm) x 11
⁄
" (300 mm) is
13
16
should end at the edge of the
should be
(l)
with the fastening screw
(l)
Fig. 8
Fig. 1
⁄
"
3
4
9
/
"
16
and
Fig. 6
.
(l)
13
Tabla de contenido
