Connecting An Ipod/Iphone; Front Panel Overview; Front Panel Display; Ir Remote Sensor - Rotel RAP-1580MKII Manual De Instrucciones

Although there are typically no video connections for a Tuner the RAP-
1580MKII can assign another video input to the Tuner input. The Video
choices are HDMI 1 - 8 (Front), Last Video Source, or Off. HDMI 1 video
input is assigned to the Tuner input, as a default setting.

Connecting an iPod/iPhone

See Figure 7
Connect the iPod/iPhone to the front USB socket.
NOTE: The audio inputs CD, PHONO, XLR, MULTI, USB, PC-USB,
BLUETOOTH, and TUNER are set to HDMI 1 video input as the factory
default. This can be changed to HDMI 1-8, Last Video Source, or Off.

Front Panel Overview

Front Panel Display

3
The Display on the front panel shows the complete OSD menu of the unit.
When the OSD is not in use, the display shows the volume, DSP mode,
source selected and type of audio mode the unit is in receiving or processing.

IR Remote Sensor

2
This sensor receives IR signals from the remote control. Do not block this sensor.
NOTE: The remainder of the buttons and controls on the front panel
are described in the Overview of Buttons and Controls section.

Remote Control Overview

The RAP-1580MKII is supplied with an easy to use remote control RR-CX100.
The RR-CX100 can be configured to use IR codeset 1 or IR codeset 2 in case
the unit is conflicting with other Rotel models. Push and hold the TUNER
button and 1 (or TUNER and 2 for codeset 2) at the same time and hold for
approximately 5 seconds until the backlights on the remote control blink on
then off then release both buttons. This sets the remote control to use codeset
1 (or codeset 2 if TUNER and 2 are held). The System menu in the OSD
includes a configuration option to set the processor to either codeset 1 or
codeset 2. The factory default for the remote and processor is codeset 1.
The RR-CX100 can also control an attached Rotel CD player. The CD player
functions include Play, Stop, Pause, Track Forward, Track Back, Fast Forward,
Fast Reverse. To activate these functions press the CD button on the remote.
If the CD is attached to the XLR source input these functions can be activated
by pressing the XLR button. To change the CD player functions to operate
after pressing the XLR button press and hold the XLR and 1 button for 5
seconds until the backlight LEDs blink two times then release. To disable
XLR sending the CD control functions press and hold the XLR and 0 button
for 5 seconds until the backlight blinks.
The transport buttons will only operate for CD control after the CD or XLR
button is pressed on the remote. If a different input is selected from the
remote these buttons will no longer send the CD transport IR commands.

Overview of Buttons and Controls

STANDBY and Power ON/OFF Buttons 1
The front-panel STANDBY button and the remote control ON/OFF button
activate or deactivate the unit. The rear panel master POWER switch must
be in the ON position for the remote standby function to operate.
VOLUME Knob and VOLUME UP/DOWN Buttons
The VOLUME UP/DOWN buttons on the remote and the large rotary control
on the front panel provide the master VOLUME control, adjusting the output
level of all channels simultaneously from mute, 1 to 96.
DISPLAY (DISP) Button
=B
Push this button to toggle between TFT and TV display mode.
MENU/SETUP Button
7H
Navigating and ENTER Buttons
The MENU/SETUP button displays the OSD setup screen on the front display
and HDMI OSD enabled output. Push the MENU/SETUP button again to
deactivate this menu. Use the navigation buttons Up/Down/Left/Right and
ENTER on the remote control or front panel to access the various menus.
MUTE Button
qF
Push the MUTE button once to turn the sound off. An indication appears in
the front panel and on the on-screen display if using HDMI inputs 4 to 8.
Press the button again to restore the previous volume level.
INPUT Buttons
6M
The INPUT button on the front panel can be used to display the input source
menu. The input source can be changed by selecting the desired source
with the navigation buttons and pressing the ENTER button on the front
panel. The remote control input buttons can change the source directly by
pressing the desired source input.
SUR+ Buttons
-B
The SUR+ buttons on the remote control or front panel will display surround
mode information of currently selected source. The default DSP mode can
be configured in the Setup menu for each source. Press the SUR+ button
repeatedly to toggle through the available DSP modes.
DSP processing options vary depending on the selected source input type.
Not all DSP options are available in analog or digital input modes.
Other buttons on the remote can directly access specific DSP modes.
2CH: Changes the audio mode to STEREO, DOWN MIX.
BYPASS: Bypass all DSP processing.
PLCM: Selects Dolby ATMOS surround mode.
Playback Control buttons
L
These buttons provide basic control functions for iPod/USB AUDIO playback.
Supported functions include Play, Stop, Pause, Next Track, Previous Track.
DIM Button
J
Use this button to dim the front panel display.
Adjustment made using the J
after power off.
A
4D
5I
button is temporary only and not saved
19