Tabla de contenido
Idiomas disponibles
Idiomas disponibles
2) GENERAL OUTLINE
This controller is suitable for residential use and has been designed for swing
gates with particularly large gate posts. The drive arm, built with a special anti-
shearing shape, allows the leaves to be moved when the controller is conside-
rably out of place with respect to the fulcrum of the leaves. The non-reversible
electro-mechanical gearmotor maintains the stop during closing and opening.
The release knob with personalised key, fitted outside each operator, makes
manual manoeuvre extremely easy.
WARNING! The installation, the maintenance and the repair should be done by
responsible and qualified persons with an updated knowledge of the current safety
standards. It's strictly forbidden to service the automation when the power is on.
ATTENTION! The IGEA model controller is not equipped with mechanical torque
adjustment. It is compulsory to use a control panel of the same manufacturer, in
compliance with the basic safety requirements of directives 2014/35CEE, 2014/30/
CEE, 2006/42/CEE equipped with appropriate electric adjusment of the torque.
3) TECHNICAL SPECIFICATIONS
Voltage: .................................................................................................... 220-230V~ 50/60Hz
Motor: .................................................................................................Single-phase 1400min
Power: .................................................................................................................................... 300W
Absorption: ......................................................................................1.7A (230V); 3,4A (110V)
Capacitor: ................................................................ 10µF 450V (230V); 40µF 250V (110V)
Insulation class: ............................................................................................................................F
Thermal protection: ...............................................................................130°C self-resetting
Lubrication: ................................................................................................. Permanent grease
Reduction ratio: .................................................................................................................. 1/812
Output revs.: ..........................................................................................................1.7 min
Opening time 90°: ..................................................................................................................15s
Torque provided: ............................................................................................................ 320Nm
Max. leaf weight and length: .............................2000N (~200kg) for 2.5m leaf length
Impact reaction: ........................................................ Electric clutch (with control panel)
Drive: ..............................................................................................................................Lever arm
Stopping: ...............................................................................Built-in electric limit-switches
Manual manoeuvre: ............................................Release knob with personalised key.
Number of manoeuvres: ........................................................................................ 15 cycle/h
Working temperature: ...................................................................................-15 C° ÷ +55 C°
Protection: .............................................................................................................................. IP 44
Controller weight: ..............................................................................................160N (~16kg)
Dimensions: ....................................................................................................................See fig.1
In case the motor tours in the opposite side, you should invert the running buckle
"M" of the operator. Refer to the relevant instruction manual for connection of
the control panel.
4) OPERATOR INSTALLATION
WARNING! Refer to Fig.A for CORRECT installation.
4.1) Preliminary checks
Check that:
•
The gate structure is sufficiently sturdy and rigid.
The fixing position must be worked out according to the leaf structure. In any
case, the manoeuvring arm must push against a reinforced leaf point (fig. 2).
•
The leaves can be moved manually along their entire stroke.
If the gate has not been installed recently, check the wear condition of all its
components. Repair or replace defective and worn parts.
Operator reliability and safety are directly affected by the condition of the
gate structure.
4.2) Fitting of the manual release knob
•
With reference to fig. 9, position release knob "A" on flange "B" prefitted on
the cover.
•
Insert adapting ring "C" in the bush with release tooth "D".
WARNING: Depending on the operator installation position (right or left
side), insert ring "C" and position bush "D" as shown in fig. 9.
•
Insert space washer "E" and then shimming thrust bearing "F" into bush "D"
on the release tooth side.
•
Secure everything, using appropriate self-tapping screw "G" inside the operator
cover, checking the correct positioning of ring "C" and bush "D".
•
Close the operator cover, using the appropriate screws supplied.
WARNING: The release tooth on bush "D" must be inserted in the release
lever as shown in fig. 9b. Otherwise, the emergency manoeuvre cannot
be carried out.
Insertion is made easy by turning knob "A" to the side opposite to that for
manual release (clockwise in the case of a left-hand leaf, anticlockwise in
the case of a right-hand leaf ) and locking it in such position by means of the
appropriate key.
Check that bush "D" is placed horizontally (fig. 9b) and close the cover by positioning
its front side (the one with the release knob) as indicated in fig. 9c.
•
Before connecting the operator to the power supply, manually check that
the release knob operates correctly.
5) FIXING OF SUPPORTING PLATE (Fig.2)
The controller is supplied complete with anchoring bracket and lever arm.
Once the reinforcement point of the leaf has been identified with the gate closed,
22 -
IGEA
INSTALLATION MANUAL
-1
2500N (~250kg) for 2m leaf length
draw an imaginary horizontal line from the centre of the reinforcement point
to the gate post (fig.2). Position the anchoring bracket according to the values
given in fig. 2 for openings of up to 90° or in fig.3 for openings greater than 90°
up to a maximum of 125°.
The bracket fixing position must be flat and parallel to the leaf. Use screws or
expansion bolts which are suited to the type of gate post. If the surface of the
gate post is not regular, use expansion bolts with studs so that the parallel plate
of the leaf can be adjusted (fig.4).
•
Fasten the gearmotor to the gate post using the 4 screws, pointing the ge-
armotor to the left or the right (fig.5).
•
Assemble the lever arm as shown in fig.6.
DX= assembly on the right leaf
SX= assemby on the left leaf
Choose the most suitable position of 'F' bracket for the fastening to the leaf.
•
Insert the square of the first lever in the output shaft of the gearmotor and
fasten it (fig.7).
•
Release the operator by turning the release knob to allow easy movement of
the arm (see paragraph on "EMERGENCY MANOEUVRE").
-1
•
The correct position for the controller arm is shown in fig.8.
The leaf fixing point can be identified by positioning the arm so that it is in
accordance with the distance shown in fig.8.
•
Fix the angular towing bar "F" to the leaf by welding or using screws.
•
With the controller released, check the correct movement of the arm.
•
Repeat the same operation for the other leaf, if installed.
6) ELECTRICAL INSTALLATION SET-UP
max
Arrange the electrical installation as shown in fig.10.
The power supply connections must be kept separate from the auxiliary con-
nections (photocells, sensitive edge, etc.). Fig.10 shows the cross-section and
the number of connections.
In fig.11 you will find the junction-box of the operator and the position of the
cable holder which should be fixed with an adequate tightening of the bolt. In
case the motor tours in the opposite side, you should invert the running buckle
"M" of the operator. Refer to the relevant instruction manual for connection of
the control panel. Inside the operator the cable must be kept far from those parts
which can be hot.
7) LIMIT-SWITCH SETTING
•
Position the limit-switch reference cams "R-FC1" and "R-FC2" as shown in fig.
12, without tightening the fixing screws.
•
Identify the opening and closing limit switches (FC1 and FC2) keeping in mind
that:
In the left-hand operator (fig. 13):
FC1 corresponds to the OPENING limit switch
FC2 corresponds to the CLOSING limit switch
In the right-hand operator (fig. 14):
FC1 corresponds to the CLOSING limit switch
FC2 corresponds to the OPENING limit switch
•
When the gate is fully closed or opened, rotate the corresponding cam until
you perceive the click of the limit microswitch concerned, and lock it in po-
sition by tightening the appropriate screws as shown in fig. 12.
•
Check that the limit switches intervene correctly, initiating a few complete
motor-driven opening and closing cycles.
•
Fit the cover on the operator.
•
f the control panel is provided with operation-time setting, this must be set
to a value slightly greater than that needed for limit-switch intervention.
•
Control the operator through the control board Libra.
8) ADJUSTMENT OF LEAF PHASE DISPLACEMENT
In case of gates with two leaves, the control panel should include a delay setting
function on closing of the second leaf to guarantee a correct closing manoeuvre.
For the wiring of the motor which should close with a slight delay, refer to the
instructions for the control panel installed.
9) MOTOR TORQUE ADJUSTMENT
WARNING: Check that the impact force value measured at the points
established by the EN 12445 standard is lower than that specified in
the EN 12453 standard.
The adjustment of the motor torque (anti-squashing) is performed on the
control panel. See control unit instruction manual.
The adjustment should be set for the minimum force required to carry out the
opening and closing strokes completely observing, however, the limits of the
relevant standards in force.
CAUTION! Excessive torque adjustment may jeopardise the anti-squash safety
function. On the other hand insufficient torque adjustment may not guarantee
correct opening or closing strokes.
10) EMERGENCY MANOEUVRE (Fig. 15)
In the case of power failure or operation malfunctions, manual emergency mano-
euvre can be carried out by turning the external release knob with personalised key.
Tabla de contenido
