Phonic i2600 Manual Del Usuario página 14

So, a Cutom Filter can be set in its parameters, as follow:
9.1b.1. If selected a Custom_2nd filter
Output[x] [Name] HPF
->Custom_2nd F = 250Hz
→ Filtx F= 250Hz Q = 0.3
9.1b.2. If selected a Custom_3rd filter
Output[x] [Name] HPF
->Custom_3rd F = 250Hz
→ Filtx F= 250Hz Q = 0.3
9.1b.3. If selected a Custom_4th filter
Output[x] HPF
[Name]
F = 250Hz
->Custom_4th
→ Filtx F= 250Hz Q = 0.3
Once editing the Cells "Filtx", pressing the Enter Button can be accessed also for the Custom Filters the page for the fast
frequency setting, as available for the NOT Custom Filters and which way of working is described at the point 9.1a.
10. Output[x] [Name] LPF
Y F = 20.0 Hz (Y = Bypass OR Filter Type/Order, where filter type can be Buttw_1st, Buttw_2nd,
LRiley_2nd, Bessel_2nd, Buttw_3rd, Buttw_4th, Lriley_4th, Bessel_4th,
Custom_2nd, Custom_3rd, Custom_4th)
-> Y F = 20.0 Hz
Through the PM2, it is possible to Bypass the filter or to select one of the 11 available
filters' type/orders, and through the PM3 to set the HP cutting Frequency (quick fine tuning by 1Hz steps).
Once selected the filter Type and pressing again the ENTER button can be accessed the selected
filter's Fast Freq.Selection page.
10.1 Output[x] [Name] LPF
-> Y F = 20.0 Hz
10.1a. If you selected a filter from Buttw_1st up to Bessel_4th, then
the filter's Cutting Frequency can be set as follow:
Output[x] [Name] LPF
-> Edit Freq = 250Hz
10.1b. If you selected a Custom Filter (from 2
from the filter's order, the cascade od second order Cells building
the filter are available for editing in their Freq and Q parameter,
indepndently.
For proceeding with the editing of a custom filter Cell, the PM1 is
here used foir the Cell selection.
So, a Cutom Filter can be set in its parameters, as follow:
10.1b.1. If you selected a Custom_2nd filter
Output[x] LPF
[Name]
F = 250Hz
->Custom_2nd
→ Filtx F= 250Hz Q = 0.3
10
[2 order Cells selection]
nd
Ord Cell x ] x=1
[2
nd
:
x=1
Ord Cell x ] x=1
[2
nd
:
[Q not available] x=2
Ord Cell x ] x=1
[2
nd
:
x=2
Freq Fast Selection
ONLY in Freq Editing Mode
[Thousands Editor]
[Freq.] 1000Hz
:
20000Hz
up to 4 order), depending
nd th
[2 order Cells selection]
nd
Ord Cell x ] x=1
[2
nd
:
x=1
[Freq.] 20Hz [Q] 0.05
:
20kHz 10.00
[Freq.] 20Hz [Q] 0.05
:
20kHz 10.00
[Freq.] 20Hz [Q] 0.05
:
20kHz 10.00
[Filt Type] Bypass [Freq.] 20Hz
:
Custom_4th
[Hundreds Editor] [Units Editor]
100Hz
[Freq.] [Freq.]
:
900Hz
[Freq.] 20Hz [Q] 0.05
:
20kHz 10.00
:
:
:
:
20kHz
1Hz
:
100Hz
:
i2600