Intended Use; General Safety Instructions - wolfcraft 6902 Manual De Instrucciones Original

INTENDED USE

The MASTER cut 2500 is a precision saw table and work station. It is suitable for:
• Mounting a circular hand saw with riving knife on the machine plate with a max. saw blade diameter of 200 mm
and max. cutting depth of 70 mm. Do not use saws with base plate dimensions greater than the maximum values indicated
(see Fig. 13).
The appropriate split insert must be used. This makes it a stationary circular saw bench.
• Use as a circular saw bench for circular hand saws without a riving knife. Only in conjunction with separate riving knife accessory,
art. no. 6916000 with a max. saw blade diameter of 160 mm and min. cutting width of 2.4 mm.
• Use as a circular saw bench for circular hand saws without a riving knife. Only in conjunction with separate riving knife accessory,
art. no. 6917000 with saw blade diameters from min. 161 mm to max. 200 mm, a min. cutting width of 2.4 mm
and a max. cutting depth of 66 mm.
• Use as a guided circular saw on the guide rail for processing large objects like doors, worktops, etc. The machine plate
with the split insert guide rail serves as a guide block for the guide rail here.
• Use as a jigsaw table. The split insert for jigsaws and routers must be used.
• Mounting a mitre saw. The mitre saw must be securely mounted in the designated slots with the fastening materials supplied.
• Use as a milling table only in conjunction with the parallel milling guide, art. no. 6901000 and for routers with 230 V
and max. 1800 W. Do not use router bits with a diameter exceeding 27 mm. The routing machine must not be used
in conjunction with the guide rail. The split insert for routers and jigsaws with the spacer rings must be used.
• Use as a working table for machining workpieces (e.g. drilling, sanding, etc.). The workpieces can be securely fastened
in the clamping holes in the worktop using the wolfcraft one-hand clamps (art. no. 3036000).
• Observe the manufacturer's safety instructions for the machines used as well as the safety instructions for the machine table.
• When disposing of the MASTER cut 2500, please observe local disposal regulations.
The user is liable for any damage or accidents resulting from improper use.

GENERAL SAFETY INSTRUCTIONS

• Keep your workplace clean and well lit. Poor housekeeping or unlit working areas may result in accidents.
• Do not work with power tools in an explosive ambience, where flammable liquids are kept and where gas or dust occur. Power
tools will generate sparks which might ignite the dust or vapours.
• Keep children and other persons off your workplace, while using power tools. When getting distracted you can lose the control
over the equipment.
• The plug of the power tool must fit into the socket. The plug must not be tampered with. Do not use adapters together with
grounded power tools. Unmodified plugs and matching sockets will reduce the risk of getting an electric shock.
• Keep power tools out of the rain and away from wetness. Water penetrating into a power tool will heighten the risk of getting an
electric shock.
• When working with a power tool outside, use only extension cords that are suitable for outdoor use. Using an extension cord
that is suitable for outdoor use will reduce the risk of getting an electric shock.
• If it is unavoidable to use a power tool in a wet ambience, use a residual-current circuit-breaker. It will reduce the risk of getting
an electric shock.
• Take care of what you do and handle the power tool with care. Never use a power tool, when you feel tired or when you are
under the influence of drugs of any kind or alcohol. One moment of inat-tentiveness while using the power tool can cause severe
injuries.
• Do wear suitable personal protective clothing and equipment, such as hearing protection, goggles, dust masks while doing dust-
generating jobs as well as protective gloves, when processing rough materials and when changing tools.
• Remove the setting tools or wrenches before switching on the power tool. A tool or wrench at-tached to a rotating part of the
equipment may cause injuries.
• Wear suitable clothes, i.e. no loose garments or jewellery. Keep your hair, clothing and gloves away from rotating parts. Loose
garments, jewellery or long hair may be caught by such rotating parts.
• Always use the protective hood with the dust extractor.
• Do not use power tools with a defective switch. A power tool that can no longer be switched on or off is dangerous and needs
repairing.
• Keep unused power tools out of the reach of children. Do not allow persons using equipment which they are not familiar with
it, or persons who have not read these instructions. Power tools pose a danger, when being used by inexperienced persons.
• Check before starting to work, whether equipment and tools function properly. Never work with damaged or blunt tools.
• Have your power tools only repaired by duly qualified personnel. Demand original spares, so that the safety of the power tool
remains ensured.
• Pull the plug from the socket and/or remove the battery pack from the power tools before you change the setting of your
equipment or before you replace any components. The unin-tentional re-start of a power tool may cause accidents.
• Put up the machine table properly before installing the power tool. The table's safe assem-bly is vital to prevent it from collapsing.
• Attach the power tool safely to the machine plate before using it. If the power tool gets out of place on the machine plate, you may
lose control of it.
• Put the machine table on a firm, plain and horizontal surface. If the machine table can shift or wobble, neither the power tool nor
the work piece can be moved safely and steadily.
• Do not overload the machine table and do not use it as ladder or scaffolding. Excess loads or standing on the machine table can
shift the table's centre of gravity upwards, so that it may topple over.
• Do not process any other materials than wood or easily machinable plastic. Exception: It is also allowed processing easily machinable
metals (e.g. aluminium), but only with the jig-saw and a suitable saw blade
• Loose splinters, chips or similar residues must not be removed by hand from the area close to the running saw blade!
t
43