Milwaukee 2606-059 Manual De Instrucciones página 16

APPLICATIONS
To reduce the risk of electric shock,
WARNING
check work area for hidden pipes
and wires before drilling or driving screws.
Drilling in Wood, Composition Materials
and Plastic
When drilling in wood, composition materials and
plastic, select the
Start the drill slowly, gradually increasing speed as
you drill. When drilling into wood, use wood augers
or twist drill bits. Always use sharp bits. When using
twist drill bits, pull the bit out of the hole frequently to
clear chips from the bit flutes. To reduce the chance of
splintering, back work with a piece of scrap wood. Se-
lect low speeds for plastics with a low melting point.
Drilling in Metal
When drilling in metal, select the
ating mode. Use high speed steel twist drills or hole
saws. Use a center punch to start the hole. Lubricate
drill bits with cutting oil when drilling in iron or steel.
Use a coolant when drilling in nonferrous metals such
as copper, brass or aluminum. Back the material
to prevent binding and distortion on breakthrough.
Drilling in Masonry
When drilling in masonry, select the
operating mode. Use high speed carbide-tipped bits.
Drilling soft masonry materials such as cinder block
requires little pressure. Hard materials like concrete
require more pressure. A smooth, even flow of dust
indicates the proper drilling rate. Do not let the bit
spin in the hole without cutting. Do not use water to
settle dust or to cool bit. Both actions will damage
the carbide.
Driving Screws and Nut Running
Drill a pilot hole when driving screws into thick or hard
materials. Select the
the torque selector collar to the proper position and
set the speed to low. Use the proper style and size
screwdriver bit for the type of screw you are using.
With the screwdriver bit in the screw, place the tip of
the screw on the workpiece and apply firm pressure
before pulling the trigger. Screws can be removed
by reversing the motor.
Overloading
Continuous overloading may cause permanent dam-
age to tool or battery pack.
Importado por:
Techtronic Ind Argentina SRL
Cuit: 33-71069847-9
Av. Leandro N. Alem 110 piso 13
C.A.B.A (1001), BUENOS AIRES
ARGENTINA
58149908d3
drill-only operating mode.
drill-only oper-
hammer drill
driving screws mode. Set
MILWAUKEE TOOL
MAINTENANCE
To reduce the risk of injury, always
WARNING
unplug the charger and remove the
battery pack from the charger or tool before
performing any maintenance. Never disassemble
the tool, battery pack or charger. Contact a MIL-
WAUKEE service facility for ALL repairs.
Maintaining Tool
Keep your tool, battery pack and charger in good
repair by adopting a regular maintenance program.
Inspect your tool for issues such as undue noise,
misalignment or binding of moving parts, breakage of
parts, or any other condition that may affect the tool
operation. Return the tool, battery pack, and charger
to a MILWAUKEE service facility for repair. After six
months to one year, depending on use, return the
tool, battery pack and charger to a MILWAUKEE
service facility for inspection.
If the tool does not start or operate at full power with
a fully charged battery pack, clean the contacts on
the battery pack. If the tool still does not work prop-
erly, return the tool, charger and battery pack, to a
MILWAUKEE service facility for repairs.
To reduce the risk of personal in-
WARNING
jury and damage, never immerse
your tool, battery pack or charger in liquid or
allow a liquid to flow inside them.
Clean dust and debris from vents. Keep handles
clean, dry and free of oil or grease. Use only mild
soap and a damp cloth to clean, since certain clean-
ing agents and solvents are harmful to plastics and
other insulated parts. Some of these include gasoline,
turpentine, lacquer thinner, paint thinner, chlorinated
cleaning solvents, ammonia and household deter-
gents containing ammonia. Never use flammable or
combustible solvents around tools.
For repairs, return the tool, battery pack and charger
to the nearest service center.
ACCESSORIES
Use only recommended accesso-
WARNING
ries. Others may be hazardous.
For a complete listing of accessories, go online to
www.milwaukeetool.com or contact a distributor.
Importado por:
Techtronic Industries Comércio de
Ferramentas do Brasil Ltda.
Prolongamento da Travessa Claudio Armando,
nº 171, Bloco 2, galpão 21.
Bairro Assunção, São Bernardo do Campo, SP.
CEP: 09861-730 – Brasil
CNPJ: 11.857.988/0001-26
01/16
Cleaning
Repairs
961011803-01(B)
Impreso en China