Hitachi Koki CL 10D2 Instrucciones De Manejo página 8

English
(3) Push the forward/reverse switching button from the
left as shown in Fig. 4-3 to set to the
With the button held down, pull the trigger switch
so that the cutter can be removed from the stud.
Only set to this position if the rechargeable battery
is worn out and the unit stops operating during
cutting. Immediately turn off the switch after the
cutter has been removed from the stud.
If you remove your finger, the forward/reverse
switching button automatically returns to the
position (Fig. 4-2).
CAUTION:
Do not attempt to cut in the
3). If you attempt to cut in this position, there will
be an overload on the motor and cutting will not
be possible. Never apply excessive force to the
main unit as this can cause damage to the unit.
Forward/reverse switching button
(Equipment as seen from the handle side)
Does not
During cutting
rotate
operations
Fig. 4-1
4. Check the cutter size, attachment direction,
attachment bolt and spacer
(1) The cutter size differs according to the size of the
studs to be cut. Make sure that a cutter is attached
that conforms to the size of the studs to be cut.
(2) Cutter attachment includes directionality. Make sure
that the cutter has been attached so that the side
without the notch on the cutter can be seen on
bracket (A) (movable side) when the main unit is
viewed from the front or that the notch on the cutter
surface can be seen on bracket (B) (fixed side).
Bracket (A)
(movable side)
Hex. socket
hd. bolt
Spacer
(used only with
M6, M8 or M10)
7
position.
position (Fig. 4-
Removal during
cutting operations
Fig. 4-2 Fig. 4-3
Side without
notch
Notch side
Spacer
(used only with
M6, M8 or M10)
Bracket (B)
(fixed side)
Fig. 5
(3) Use the accessory hexagonal wrench to insure that
the hex. socket hd. bolt for attaching the cutter is
securely tightened (Fig. 5). Using the equipment
while the bolt is loose could cause damage to the
main unit and cutter.
(4) Depending on the size of the studs it may be
necessary to attach special spacers to the cutter.
1 When using the M10, M8 or M6 cutter
Check and confirm that the accessory M6, M8 or
M10 spacers are correctly inserted respectively
between bracket (A) and the cutter and bracket (B)
and the cutter (Fig. 5).
CAUTION:
If the spacers are not attached or if spacers of the
wrong size are used, the threads of the cutter and
the studs will not properly mesh, thereby causing
damage to the studs and the cutter edge. Be sure
to attach spacers correctly.
2 When using the W3/8" cutter
No spacers are required. Check and confirm that
only the cutter is attached.
For details, refer to the section on "Cutter life and
replacement" on page 9.
5. Correctly insert the stud guide
The stud guide is used to prevent tilting during
cutting of studs. Correctly adjust the dial calibration
to the mark ( ) depending on the size of the stud
to be cut (Fig. 6).
CAUTION:
If the size of the stud and the dial position to do
not agree, the cut section may be subjected to burrs
or its shape may be distorted, which may result in
damage to the main unit.
Dial
HOW TO USE
CAUTION:
Never bring the cutter near your fingers when
operating the trigger switch.
When cutting short studs, take caution as to not
place your fingers in the space between the short
stud and main unit, such as the guard section (see
Fig. 7), battery, etc.
After cutting, the cut section of the stud is very
sharp and therefore dangerous. Be very careful
when handling the stud.
Screw size
display
Mark
Stud guide
Fig. 6