Working Advice; Maintenance And Service; Maintenance And Cleaning; After-Sales Service And Application Service - Bosch GLL 2-10 Professional Manual Original

OBJ_BUCH-2825-002.book Page 17 Wednesday, August 24, 2016 4:01 PM
– The difference d between point III and the centre of the la-
ser line at the upper edge of the door opening results in the
actual deviation of the measuring tool from the vertical
plane.
– Measure the height of the door opening.
The maximum permitted deviation d
lows:
d = double height of the door opening x 0.3 mm/m
max
Example: With a door opening height of 2 metres, the maxi-
mum permitted deviation is
d = 2 x 2 m x 0.3 mm/m = 1.2 mm. Thus, the marks must
max
not be more than 1.2 mm apart.

Working Advice

 Always use the centre of the laser line for marking. The
width of the laser line changes with the distance.
Working with the Tripod (Accessory)
A tripod offers a stable, height-adjustable measuring support.
Position the measuring tool with the 1/4" tripod mount 12 on-
to the thread of the tripod 15 or a commercially available cam-
era tripod. For fastening to a commercially available construc-
tion tripod, use the 5/8" tripod mount 11. Tighten the
measuring tool with the tripod mounting stud.
Laser Viewing Glasses (Accessory)
The laser viewing glasses filter out the ambient light. This
makes the red light of the laser appear brighter for the eyes.
 Do not use the laser viewing glasses as safety goggles.
The laser viewing glasses are used for improved visualisa-
tion of the laser beam, but they do not protect against laser
radiation.
 Do not use the laser viewing glasses as sun glasses or in
traffic. The laser viewing glasses do not afford complete
UV protection and reduce colour perception.
Fastening with the Universal Holder (Accessory)
(see figure D)
With the universal holder 20, you can fasten the measuring
tool, e.g., to vertical surfaces, pipes or magnetisable materi-
als. The universal holder is also suitable for use as a ground tri-
pod and makes the height adjustment of the measuring tool
easier.
– Adjust the universal holder roughly before 20 switching on
the measuring tool.
Working with the Measuring Plate (Accessory)
(see figures G–H)
With the measuring plate 16, it is possible to project the laser
mark onto the floor or the laser height onto a wall.
With the zero field and the scale, the offset or drop to the re-
quired height can be measured and projected at another loca-
tion. This eliminates the necessity of precisely adjusting the
measuring tool to the height to be projected.
The measuring plate 16 has a reflective coating that enhances
the visibility of the laser beam at greater distances or in in-
tense sunlight. The brightness intensification can be seen on-
ly when viewing, parallel to the laser beam, onto the measur-
ing plate.
Bosch Power Tools
Work Examples (see figures D–F)
Applicational examples for the measuring tool can be found
on the graphics pages.

Maintenance and Service

is calculated as fol-
max

Maintenance and Cleaning

Store and transport the measuring tool only in the supplied
protective pouch.
Keep the measuring tool clean at all times.
Do not immerse the measuring tool in water or other fluids.
Wipe off debris using a moist and soft cloth. Do not use any
cleaning agents or solvents.
Regularly clean the surfaces at the exit opening of the laser in
particular, and pay attention to any fluff or fibres.
In case of repairs, send in the measuring tool packed in its
protective pouch 13.

After-sales Service and Application Service

Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can al-
so be found under:
www.bosch-pt.com
Bosch's application service team will gladly answer questions
concerning our products and their accessories.
In all correspondence and spare parts orders, please always
include the 10-digit article number given on the nameplate of
the product.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange
the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail: [email protected]
Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: (01) 4666700
Fax: (01) 4666888
English | 17
1 609 92A 3G0 | (24.8.16)