Clothing Care - Sears KENMORE ELITE Oasis 110.2803 Serie Manual De Uso Y Cuidado

Is the water inlet hose kinked?
Straighten the hoses.
Wash/Rinse temperature
Does the water level seem too low, or does the washer
appear to not fill completely? •
The top of the agitator is much higher than the highest water
level. The Auto Water Level feature senses the size of the load
and adds the correct amount of water for the load size. You
may notice during a cycle that the wash load is not •
completely submerged in water. This is normal.
Are you using Auto Water Level?
The Auto feature senses the size of the load and adds the
correct amount of water for the load size. You may notice
during a cycle that the wash load is not completely
submerged in water. This normal for your washer.
Has a household fuse blown, or has a circuit breaker
tripped?
Replace the fuse or reset the circuit breaker. If the problem
continues, call an electrician.
Is the washer in a normal pause in the cycle?
The washer may pause for about 2 minutes during certain
cycles. Allow the cycle to continue. Some cycles feature
periods of agitation and soak.
Is the washer overloaded?
Wash smaller loads. See "Starting Your Washer" for
maximum load size.
Is the lid open?
The lid must be closed during operation. The washer will not
operate with the lid open.
Did you add more items to the load once the washer
started?
Once the load is wet, there may appear to be space for more
items. Do not add more than 1 or 2 garments after the cycle
has started. For best results determine load size with dry items
only.
Washer continues to fill or drain, or the cycle seems
stuck
Is the top of drain hose lower than the control knobs on
washer?
The top of the drain hose must be at least 39" (99 cm) above
the floor. See "Drain System."
Does the drain hose fit too tightly in the standpipe, or is it
taped to the standpipe?
The drain hose should be loose yet fit securely. Do not seal
the drain hose with tape. The hose needs an air gap. See
"Installation Instructions."
Washer won't drain or spin; water remains in washer
• Is the drain hose clogged, or the end of the drain hose
more than 96" (244 cm) above the floor?
See "Drain System."
• Is the lid open?
The lid must be closed during operation. The washer will not
operate with the lid open.
Are the hot and cold water inlet hoses reversed?
If the hot and cold water inlet hoses are reversed, the washer
will display an "HC" error code at the end of the cycle. See
"Connect the Inlet Hoses."
Are you washing many loads?
As your frequency of loads washed increases, the water
temperature may decrease for hot and warm temperatures.
This is normal.
Do you have an ENERGY STAR washer?
The wash water temperatures may feel cooler to you than
those of your previous washer. This is normal.
Does the wash water temperature feel lower than usual?
As washing progresses, the wash temperature will decrease
slightly for hot and warm washes. This is normal.
To reduce wrinkling, the warm rinse is regulated to be cooler
than the warm wash.
Excessive sudsing
Is there excessive sudsing?
Always measure detergent. Follow detergent manufacturer's
directions. If you have very soft water, you might need to use
less detergent.
Was the cycle interrupted and then the Stain Treat option
selected?
The Stain Treat option should be started on a dry load only.
The Stain Treat option should not be selected after the tub
has started filling with water.
Water remaining in bottom of dispenser
• Did the dispenser drain properly?
A small amount of water will be left in the dispenser at the
end of the cycle. This is normal.
Cycle did not run Stain Treat option
Did you select the Stain Treat option?
The Stain Treat option must be selected for it to be included
in a wash cycle. The Stain Treat option should be started on a
dry load only. Stain Treat should not be selected after the tub
has started filling with water.
• The Stain Treat option is a default option in the Heavy Duty
cycle and may be added to other cycles.
Load too wet
• Did you use the right cycle for the load being washed?
Select a cycle with a higher spin speed or select Drain & Spin.
• Did you use a cold rinse?
Cold rinses leave loads wetter than warm rinses. This is normal.
Did you wash an extra large load?
A large unbalanced load could result in a reduced spin speed
and wet clothes at the end of the cycle. Evenly distribute the
load and make sure the height of the load does not exceed
the top row of basket holes.
22