Dispenser Operation; Washer Operation - Sears KENMORE ELITE Oasis 110.2803 Serie Manual De Uso Y Cuidado

Noisy, v ibrating, off-balance
Is the floor flexing, sagging or not level?
Flooring that flexes or is uneven can contribute to noise and
vibration of the washer. A 3/4"(1.9 cm) piece of plywood under
the washer will reduce the sounds. See "Location
Requirements."
Is the washer level? Does the washer rock when pushed
against the corners?
The washer must be level. The front and rear feet must be in
firm contact with the floor. Check that the lecknuts are
tightened. See "Level the Washer."
Is the load balanced?
Evenly distribute the load in the washer basket and make
sure the height of the load does not exceed the top row of
basket holes. See "Starting Your Washer."
Do you hear clicking or other noises when the cycle
changes from washing to draining or spinning?
When the the drive system shifts or the washer basket settles
between cycles you may hear noises that are different from
your previous washer. These are normal washer noises.
Is the washer gurgling or humming?
When the washer drains, the pump will make a continuous
humming with periodic gurgling or surging sounds as the final
amounts of water are removed. This is normal.
Are you washing a small load?
You will hear more splashing sounds when washing small
loads. This is normal.
The washer basket moves while washing.
This is normal.
Washerleaks
• Are the fill hoses tight?
Are the fill hose washers properly seated?
Check both ends of each hose. See "Connect the Inlet
Hoses."
Did you pull the drain hose from the washer cabinet and
install it in a standpipe or laundry tub?
The drain hose should be pulled from the washer cabinet and
secured to the drainpipe or laundry tub. See "Connect the
Drain Hose" and "Secure the Drain Hose."
Is the sink or drain clogged?
Sink and drainpipe must be able to carry away 17 gal. (64 L)
of water per minute. If sink or drainpipe is clogged or slow,
water can back up out of drainpipe or sink.
Is water splashing off the tub ring or the load?
The wash load should be balanced and not overloaded. If the
wash load is unbalanced or overloaded, incoming water can
deflect off the load.
Is the washer properly installed?
The washer must be level. The feet should be properly
installed and the nuts tightened. See "Level the Washer."
Was the cycle interrupted and then the Stain Treat option
selected?
The Stain Treat option should be started on a dry load only.
The Stain Treat option should not be selected after the tub
has started filling with water.
Check household plumbing (laundry tubs, faucets,
drainpipe, water pipes) for leaks.
Dispenser operation
Are the laundry products in the correct dispensers?
Add the correct amounts of detergent (powdered or liquid),
liquid chlorine bleach, or fabric softener to the correct
dispenser. You can add powdered or liquid color-safe bleach
to the detergent dispenser. Be sure to match powdered
color-safe bleach with powdered detergent or match liquid
color-safe bleach with liquid detergent. Use only liquid
chlorine bleach in the bleach dispenser.
Did you put powdered or liquid color-safe bleach into the
liquid chlorine bleach dispenser (on some models)?
Add powdered or liquid color-safe bleach directly to the
washer basket. Do not use the chlorine bleach dispenser for
color-safe bleach.
Is there water remaining in bottom of dispenser?. Did
the dispenser drain properly?
A small amount of water will be left in the dispenser at the
end of the cycle. This is normal.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
Washer won't fill, rinse or agitate; washer stops
• Is the power cord plugged into a grounded 3 prong
outlet?
Plug power cord into a grounded 3 prong outlet.
• Are you using an extension cord?
Do not use an extension cord.
• Is there power at the plug?
Check electrical source or call electrician.
Is the indicator on the Cycle control knob properly lined
up with a cycle?
Turn the Cycle Control knob to the right slightly and pull to
start.
Are the water inlet valve screens clogged?
Turn off the water and remove inlet hoses from the washer.
Remove any accumulated film or particles. Reinstall hoses,
turn on water and check for leaks.
• Are the hot and cold water faucets turned on?
Turn on the water.
21