Tips And Tricks; Troubleshooting Guide; Accessories; Repairs - Metabo TS 36-18 LTX BL 254 Manual De Instrucciones Original

en ENGLISH
If necessary:
Set table leg guide bushings.
 allen screws (55)
turn clockwise =
guide sluggish
 allen screws (55)
turn anti-clockwise =
guide moves easily.
 Further fine adjustment by means of a setscrew.
(56)
55
Setting guide bushings on front leg mount:
 Turn Allen screws (57) clockwise = guide
sluggish.
 Turn Allen screws (57) anti-clockwise =
guide moves easily.
Setting guide bushings on rear leg mount:
 Turn Allen screws (58) clockwise = guide
sluggish.
 Turn Allen screws (58) anti-clockwise = guide
moves easily.
Tighten all Allen screws diagonally and
evenly.

11. Tips and Tricks

 Before cutting a workpiece to size make trial
cuts on pieces of scrap.
 Always place a workpiece on the saw table in
such way that it cannot tilt or rock (e.g. always
place a curved board on the table with the convex
side up).
 For efficient cutting of same-length cuts, use a
length stop.
 Keep surface of table clean.
22

12. Troubleshooting Guide

Before carrying out any fault service or
maintenance work, always:
1.switch machine OFF;
2.Remove battery pack.
3.Wait for saw blade to come to standstill.
Check to see that all safety devices are
operational after each fault service.
56
Motor does not run
The restart protection is active. If the battery pack
is inserted when the machine is switched on or if
the power supply is restored after an interruption,
the machine does not start:
 Switch the machine off and back on again.
Battery pack empty:
 Recharge the battery pack if performance
diminishes.
Motor overheated, e.g. by a blunt saw blade or
chip build-up in the chip case:
 Remove cause for overheating, let cool off for a
few minutes. Then restart machine.
Speed is not reached
Overload protection: There is a MAJOR reduction
in load speed.
 The motor temperature is too high! Allow the
machine to run at idle speed until it has cooled
down.
Overload protection: The motor stops during
sawing:
57
 The machine is overloaded. Reduce the load
before continuing to work.
Specified maximum speed is not reached - Motor
receiving too little battery power:
 Recharge the battery pack if performance
diminishes.
Loss of cutting performance
Saw blade blunt (possibly tempering marks on
blade body):
 Replace saw blade (see chapter 10.
Maintenance).
Chip ejection blocked
No dust collector connected or suction capacity
insufficient:
 Connect dust extraction unit or increase suction
capacity (air speed  20 m/sec at chip ejection
tube).

13. Accessories

Only use original Metabo battery packs and
Metabo accessories.
Use only accessories that fulfil the requirements
and specifications listed in these operating
instructions.
 Circular saw Power Cut, Order no.: 6.28025
– For rough and medium-fine cuts with rapid
movement and limited power requirements
58
– Good cutting results for longitudinal cuts in solid
wood
 Circular saw blade Precision Cut, order no.:
6.28059
– Very wide range of applications in wood
processing
– For very good, clean cutting results for straight
and cross cuts in soft and hard wood
 Charger: ASC Ultra,...
 Battery packs with different capacities. Only buy
battery packs only with voltage suitable for your
power tool:
LiHD, 18 V, 8,0 Ah, 6.25369
LiHD, 18 V, 5,5 Ah, 6.25342
etc.
For a complete range of accessories, see
www.metabo.com or the catalogue.
Danger!

14. Repairs

Danger!
For safety reasons, repairs to power tools
must be carried out by qualified electricians
only using original spare parts!
Please contact your Metabo service centre if you
have Metabo devices that require repairs. See
www.metabo.com for addresses.
You can download a list of spare parts from
www.metabo.com.

15. Environmental Protection

Observe national regulations on environmentally
compatible disposal and on the recycling of
disused machines, packaging and accessories.
Only for EU countries: never dispose of
power tools in your household waste! Used
power tools must be collected separately
and handed in for environmentally compatible
recycling in accordance with European Directive
2012/19/EU on waste electrical and electronic
equipment and its implementation in national
legal systems.
Battery packs may not be disposed of with regular
waste. Return faulty or used battery packs to your
Metabo dealer!
Do not allow battery packs to come into contact
with water!
Discharge the battery pack in the power tool
before disposal. Prevent the contacts from short-
circuiting (e.g. by protecting them with adhesive
tape).

16. Technical Specifications

Explanatory notes on the specifications on page 3.
Changes due to technological progress reserved.
U = Voltage of battery pack
n = No-load speed
0
v = Max. cutting speed
0
W = thickness of splitting wedge
D = saw blade diameter (outer)
d = saw blade hole (inside)
b = cutting width
a = max. base body thickness of the saw
blade
T = cutting height with vertical saw blade
90°
T = cutting height with saw blade inclination
45°
of 45°
S = saw blade swivel range
x°
L = max. cutting width with ripping fence
p
L = max. cross-section with angle guide
W
A = dimensions without machine stand
1
(lxwxh)
A = dimensions with machine stand (lxwxh)
2
S = length of saw table
L
S = width of saw table
B
m = machine weight
Direct current
The technical specifications quoted are subject to
tolerances (in compliance with the relevant valid
standards).
Emission values
These values make it possible to assess the
emissions from the power tool and to compare
different power tools. The actual load may be
higher or lower depending on the operating
conditions, the condition of the power tool or the
accessories. Please allow for breaks and periods
for assessment purposes when the load is lower.
Arrange protective measures for the user, such as
organisational measures based on the adjusted
estimates.
Typical A-effective perceived sound levels:
L = sound-pressure level
pA
L = acoustic power level
WA
K , K = uncertainty
pA WA
Wear ear protectors!