Application; Vacuuming Dry Materials; Vacuuming Liquids; Filter - Festool CT 22 E HEPA Manual De Instrucciones

– Remove the upper part by moving it forwards
horizontally,
– Empty the dirt container,
– Replace the upper part.
that both upper-part pins are fully inserted in
the recesses (1.5)!
– Close the vacuum cleaner.

Application

Vacuuming dry materials

Before using the vacuum cleaner to evacuate dry
substances, a fi lter bag must always be inserted
in the container. Then the evacuated material can
be disposed of easily.
The fi lter element becomes damp after evacuating
liquids. A damp fi lter element suffers more wear
and tear if it is used for dry materials. Accordingly,
the fi lter element should be dried or replaced with
a dry one before dry operation.

Vacuuming liquids

Do not evacuate combustible liq-
uids!
If foam or liquid escapes, stop work
immediately and empty the dirt container.
The HEPA fi lter element shall only be
used for extracting dry materials.
The fi lter bag has to be removed before evacuat-
ing liquids. We recommend use of a special wet
fi lter (452924).
When the maximum fi lling level is reached, a
bag-full indicator (2.12) automatically interrupts
extraction.
Changing the fi lter
During the following procedure, take
care not to raise dust more than is unavoidable.
Moisten the fi lter element with a water spray be-
fore removing it.
Check the fi ll level of the fi lter bag at regular
intervals. A full fi lter bag shall be replaced im-
mediately.
Check the fi lter element for damage every time
the fi lter bag is changed. Replace damaged fi lter
elements immediately.
Always insert a fi lter bag when using a HEPA fi lter
element.
Changin the fi lter bag (3.4)
Order no.:
CTL 22 E: 452970
CTL 33 E: 452971
– Open the vacuum cleaner,
Make sure

Filter

– Remove the used fi lter bag (see printed text on
fi lter bag),
– Dispose of the used fi lter bag in accordance with
statutory requirements,
– Thoroughly clean the dirt container (2.10) and
the space (3.1) for suction turbine (wipe down
with a damp cloth),
– Insert new fi lter bag (see printed text on fi lter
bag).
fi rmly onto the dust extraction fi tting (3.2)!
– Close the vacuum cleaner.
Changing the fi lter element (2.3)
Order no. (CT 22 E, CT 33 E):
Standard fi lter element: 452923
HEPA fi lter element: 493334
Do not operate machine without a fi lter element.
This may damage the motor.
– Open the vacuum cleaner,
– Remove the used fi lter element (see printed text
on the fi lter element packaging),
– Dispose of the used fi lter element in a sealed,
dust-tight bag in accordance with statutory re-
quirements,
– Thoroughly clean dirt container (2.10) and space
(3.1) for the suction turbine (wipe down with a
damp cloth),
– Fit a new fi lter element (see printed text on the
fi lter element packaging),
– Close vacuum cleaner.
Cleaning the fi lter element
To clean, move the handle (2.1) to and fro about
10 times. N.B.: You need to clean the fi lter ele-
ment only if you use the vacuum cleaner without
a fi lter bag.
After fi nishing work
• Switch off the cleaner and pull the Plug of the
mains lead out of the Plug socket.
• Wind up the mains lead (2.6).
• Empty dirt tank.
• Clean the vacuum cleaner inside and outside by
suction and wiping.
• Deposit the appliance in a dry room, safe from
unauthorised use.

Maintenance and care

Always remove the power supply plug
from the socket before carrying out any work on
the machine.
All maintenance and repair work
which requires the motor casing to be opened
may only be carried out by an authorised service
centre.
8
Press the fi lter bag sleeve (3.3)