Tabla de contenido
Idiomas disponibles
Idiomas disponibles
ADDITIONAL SPECIFIC SAFETY RULES
DO NOT OPERATE THIS MACHINE until it is
1.
completely assembled and installed according to the
instructions. A machine incorrectly assembled can
cause serious injury.
2.
OBTAIN ADVICE from your supervisor, instructor,
or another qualified person if you are not thoroughly
familiar with the operation of this machine. Knowledge
is safety.
FOLLOW ALL WIRING CODES and recommend-
3.
ed electrical connections to prevent shock or
electrocution.
KEEP KNIVES SHARP and free from rust and pitch.
4.
dull or rusted knives work harder and can cause
kickback.
5.
NEVER TURN THE MACHINE "ON" before clearing the
table of all objects (tools, scraps of wood, etc.). Flying
debris can cause serious injury.
6.
NEVER TURN THE MACHINE "ON" with the work- piece
contacting the cutterhead. Kickback can occur.
SECURE THE MACHINE TO A SUPPORTING SUR-
7.
FACE to prevent the machine from sliding, walking or
tipping over.
PROPERLY SECURE THE KNIVES IN THE CUTTER-
8.
HEAD before turning the power "ON". loose blades
may be thrown out at high speeds causing serious
injury.
9.
LOCK THE SPEED SETTING SECURELY before feeding
the workpiece through the machine. Changing speeds
while planing can cause kick-back.
AVOID AWKWARD OPERATIONS AND HAND POSI-
10.
TIONS. A sudden slip could cause a hand to move
into the knives.
KEEP ARMS, HANDS, AND FINGERS away from the
11.
cutterhead, the chip exhaust opening, and the feed
rollers to prevent severe cuts.
NEVER REACH INTO THE CUTTERHEAD AREA while
12.
the machine is running. Your hands can be drawn into
the knives.
13.
DO NOT STAND IN LINE OF THE WORKPIECE.
Kickback can cause injury.
Refer to them often and use them to instruct others.
POWER CONNECTIONS
A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and should be
protected with a time delay fuse. NOTE: Time delay fuses should be marked "d" in Canada and "T" in the US. If an extension
cord is used, use only 3-wire extension cords which have 3-prong grounding type plugs and matching receptacle which will
accept the machine's plug. Before connecting the machine to the power line, make sure the switch is (are) in the "OFF" position
and be sure that the electric current is of the same characteristics as indicated on the machine. All line connections should
make good contact. Running on low voltage will damage the machine.
Do not expose the machine to rain or operate the machine in damp locations.
MOTOR SPECIFICATIONS
Your machine is wired for 240 volt, 60 HZ alternating current. before connecting the machine to the power source, make sure
the switch is in the "OFF" position.
Failure to follow these rules may result in serious personal injury.
SAVE THESE INSTRUCTIONS.
14.
ALLOW THE CUTTERHEAD TO REACH FULL SPEED
before feeding a workpiece. Changing speeds while
planing can cause kickback.
15.
WHEN PLANING BOWED STOCK, place the concave
(cup down) side of the stock on the table and cut with
the grain to prevent kickback.
16.
DO NOT FEED A WORKPIECE that is warped, contains
knots, or is embedded with foreign objects (nails,
staples, etc.). Kickback can occur.
DO NOT FEED A SHORT, THIN, OR NARROW
17.
WORKPIECE INTO THE MACHINE. Your hands can be
drawn into the knives and/or the workpiece can be
thrown at high speeds. See the Operation section of
this instruction manual for details.
DO NOT FEED A WORKPIECE into the outfeed end of
18.
the machine. The workpiece will be thrown out of the
opposite side at high speeds.
19.
REMOVE SHAVINGS ONLY with the power "OFF" to
prevent serious injury.
20.
PROPERLY SUPPORT LONG OR WIDE WORK-PIECES.
loss of control of the workpiece can cause serious
injury.
21.
NEVER PERFORM LAYOUT, ASSEMBLY or set-up work
on the table/work area when the machine is running.
Serious injury will result.
22.
TURN THE MACHINE "OFF", DISCONNECT IT FROM
THE POWER SOURCE, and clean the table/work area
before leaving the machine. LOCK THE SWITCH IN
THE "OFF" POSITION to prevent un-authorized use.
Someone else might accidentally start the machine
and cause injury to themselves or others.
23.
ADDITIONAL INFORMATION regarding the safe and
proper operation of power tools (i.e. a safety video)
is available from the Power Tool Institute, 1300
Sumner Avenue, Cleveland, OH 44115-2851 (www.
powertoolinstitute.com). Information is also available
from the National Safety Council, 1121 Spring lake
drive, Itasca, Il 60143-3201. Please refer to the
American National Standards Institute ANSI 01.1
Safety Requirements for Woodworking Machines and
the U.S. department of labor Regulations.
4
Tabla de contenido
