Milwaukee 6065 Manual Del Operador página 7

Installing Sanding Discs (Fig. 2)
1. Unplug tool and place it upside down on a level surface as shown. Remove any accessories from spindle.
2. Thread flange and nylon washer onto spindle. Attach backing pad and sanding disc using Fig. 2 to determine type and order of assembly.
NOTE: When installing flap disc without hub, position flap disc nut as shown.
3. To tighten, press in the spindle lock button while turning disc nut clockwise.
4. To remove sanding disc and backing pad, unplug tool and reverse procedure.
Fig. 2
Disc nut
Sanding
disc
A
Backing
pads
A. Polypropylene
B. Spiral
C. Rubber
D. Phenolic
Sanding (Fig. 3)
1. Use a clamp, vise or other practical means to hold your work, free-
ing both hands to control your tool. Firmly grasp rear handle and side
handle before starting and while tool is in operation. Allow sanding
disc to come to full speed before beginning to sand.
2. Hold tool at 5° to 15° angle as shown to ensure proper sanding
pressure and control (Fig. 3). Too great an angle will result in too
much pressure and could cause excessive wear to the disc and
workpiece. Too small an angle will reduce control.
Fig. 3
For best results, use only
this portion of the disc.
3. Use long, sweeping, side to side strokes, advancing forward to
produce the desired finish.
Removing Welds or Hammer Marks
When removing welds or hammer marks, limit coarse sanding to the
immediate area. Use successively finer grits to smooth surface.
Cross Sanding
When finishing a surface that has been prepared by a coarse disc or
wheel, sand at right angles to the strokes made by the coarser disc.
Finishing marks left from previous sanding are easily seen and removed
for a uniform finish. Failure to cross sand when changing from a coarse
disc to a finishing disc may result in deep scratches and circular marks.
USING SANDING DISCS
B C
Hold at a 5° to 15° angle
D
Nylon washer
Flange
Spindle
Spindle lock button
Finishing Metal
Constantly move across the surface. Work faster on curved surfaces
where contact areas are smaller and pressure is greater. Flat areas may
appear at the end of the stroke when pressure is too heavy. Ease up on
pressure at end of each stroke and when reversing strokes.
Troubleshooting
Deep scratches and circular marks can result from:
• Using too coarse a grit
• Using a partially glazed disc
• Dirt or loose metal on the workpiece
• Failure to sand across the grain when changing from coarse to
finishing discs
Bluish discoloration of metal surface indicates:
• Excessive heat caused by circular motion in a small area
• Excessive pressure
• Use of worn out or glazed discs
Selecting Sanding Discs & Grit
Refer to the table below to select the correct type of sanding disc for your
job. Generally, use 16, 24 or 36 grit for heavy stock removal; 50, 60 or 80
grit for medium stock removal and 120 grit for finishing. Always begin
with a coarse grit, using successively finer grits to obtain the desired
finish. See Catalog for a complete list of MILWAUKEE sanding discs.
Aluminum
Oxide
For fast cutting,
general purpose discs
for most metal jobs.
Best for cold-rolled
steel, stainless steel or
metals requiring tough,
fast cutting, long last-
ing abrasives.
Flap disc
nut position
Flap disk
without hub
Rubber
Type 27
pad
flange
Aluminum
Zirconia Bi-Cut
Unique grit pattern is Lasts up to 3 times
arranged in clusters longer than aluminum
for faster stock oxide
removal and cleaning. general metal working.
Ideal for removing paint Ideal for tough jobs.
from cars, boats, etc.
without clogging.
Flap disk
with hub
Ceramic
discs. For
page 7