DeWalt DW744 Manual De Instrucciones página 10

3.Ifripping, ensure r ail l ocklever i s tight a nd fence ispar-
allel t otheblade.
4.Ifcrosscutting, miter g auge lever i stight.
5.Guard i sinplace andworking properly.
6.Safety g lasses arebeing worn.
7.The blade guard isproperly attached andtheanti-kick-
back teeth arefunctioning.
Failure t oadhere t othese common safety r ules c angreatly
increase the likelihood ofinjury.
Ripping
1. Lock the rip fence by pressing the rail lock lever down,
Remove the miter gauge.
2. Raise the blade so it is about 1/8"(3.2mm) higher than
the top of the workpiece.
3. Hold the workpiece flat on the table and against the
fence. Keep the workpiece about 1" (25.4mm) away
from the blade.
,& CAUTION: The workpiece must have a straight edge
against the fence and must not be warped, twisted or
bowed. Keep both hands away from the blade and away
from the path of the blade.
4. Turn the saw on and allow the blade to come up to
speed. Both hands can be used in starting the cut.
When there is approximately twelve (12) inches
(305mm) left to be ripped...use only one hand, with your
thumb pushing the material, your index and second fin-
ger holding the material down and your other fingers
hooked over the fence. Always keep your thumb along
side your first two fingers and near the fence.
5. Keeping the workpiece against the table and fence,
slowly feed the workpiece rearward all the way through
the saw blade. Continue pushing the workpiece until it is
clear of the guard and it falls off the rear of the table. Do
not overload the motor.
6. Never try to pull the workpiece back with the blade turn-
ing. Turn the switch off, allow the blade to stop, raise the
anti-kickback teeth on each side of the splitter if neces-
sary and slide the workpiece out.
7. When sawing a long piece of material or a panel, always
use a work support. A sawhorse, rollers, or out feed
assembly provides adequate support for this purpose. The
work support must be at the same height as the saw
table.
A CAUTION: Never push or hold onto the '_ree" or "cut off"
side of the workpiece.
Bevel Ripping
This operation is the same as ripping except the bevel angle
is set to an angle other than zero degrees.
,_ WARNING: Before connecting the table saw to the power
soume or operating the saw, always inspect the guard and
spfitter for proper alignment and clearance with saw blade.
Check alignment after each change of bevel angle.
Ripping Small Pieces
It is unsafe to rip small pieces. It is not safe to put your hands
close to the blade. Instead, rip a larger piece to obtain the
desired piece. When a small width is to be ripped and the
hand cannot be safely put between the blade and the rip
fence, use one or more push sticks. A pattern is included on
page 9 to make push sticks. Use them to hold the workpiece
against the table and fence, and push the workpiece fully
past the blade. See Figure 22.
Crosscutting
1. Remove the rip fence and place the miter gauge in the
desired slot.
2. Adjust the blade height so that the blade is about 1/8"
(3.2ram) higher than the top of the workpiece.
3. Hold the workpiece firmly against the miter gauge with
the path of the blade in line with the desired cut location.
Keep the workpiece an inch or so in front of the blade.
KEEP BOTH HANDS AWAY FROM THE BLADE AND
THE PATH OF THE BLADE.
4. Start the saw motor and allow the blade to come up to
speed.
5. While using both hands to keep the workpiece against
the face of the miter gauge, and holding the workpiece
flat against the table, slowly push the workpiece through
the blade. See Figure 23.
6. Never try to pull the workpiece with the blade turning.
Turn the switch off, allow the blade to stop, and carefully
slide the workpiece out.
i_ CAUTION: Never touch or hold onto the "free" or "cut off"
end of the workpiece.
Bevel Crosscutting
This operation is the same as crosscutting except that the
bevel angle is set to an angle other than 0°.
_ WARNING: Before connecting the table saw to the power
source or operating the saw, always inspect the guard and
splitter for proper alignment and clearance with saw blade.
Check alignment after each change of bevel angle.
Mitering
This operation is the same as crosscutting except the miter
gauge is locked at an angle other than 0°. Hold the work-
piece FIRMLY against the miter gauge and feed the work-
piece slowly into the blade (to prevent the workpiece from
moving). See Figure 23.
MITER GAUGE OPERATION
To set your miter gauge, loosen the lock handle and move
the miter gauge to the desired angle. The miter gauge has
set stops and 90 ° and 45 ° left and right. To rotate the miter
gauge beyond these stops, flip the stop plate up, as shown
in Figure 21.
Compound Mitering
This is a combination of bevel crosscutting and mitering.
Follow the instruction for both bevel crosscutting and
mitering.
8
FIG. 24
DUST ACCESS
DOOR
HAIR PIN COTTERS
FIG. 25
HEIGHT
ADJUSTMENT
THREADS
Dado Cutting
A CAUTION: Do not attempt to stack dado blades thicker
than 13/16" (20mm). Do not use dado blades larger than 8"
(200mm) diameter. When installing the dado stack, do not
include the inner clamp washer. Replace it with the outer
clamp washer, then install the blade stack, arbor nut, and
tighten with the wrench supplied.
Since dado cuts are not through cuts, the cuts must be per-
formed with the blade guard removed. To remove the blade
guard, loosen the two bolts shown in Figure 10 and remove
the guard assembly.
When using the dado, the special dado insert (also sold as
an accessory) must be used.
Anytime a cut is required that is considerably wider than the
saw ken', a dado is used. A dado cut is commonly used to
add support and line up a shelf for a cabinet, bookcase or
some such project. When using the dado, the guard must be
removed. Use EXTREME care when using the dado without
the guard. If a deep cut is required. Use several successive