Makita BTD040 Manual De Instrucciones página 5

Ocultar thumbs Ver también para BTD040:
Tabla de contenido
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 28
4.
Do not short the battery cartridge:
(1) Do not touch the terminals with any conduc-
tive material.
(2) Avoid storing battery cartridge in a container
with other metal objects such as nails, coins,
etc.
(3) Do not expose battery cartridge to water or
rain.
A battery short can cause a large current flow,
overheating, possible burns and even a break-
down.
5.
Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50°C (122°F).
6.
Do not incinerate the battery cartridge even if it
is severely damaged or is completely worn out.
The battery cartridge can explode in a fire.
7.
Be careful not to drop, shake or strike battery.
8.
Do not charge inside a box or container of any
kind. The battery must be placed in a well venti-
lated area during charging.
ADDITIONAL SAFETY RULES FOR TOOL
1.
Be aware that this tool is always in an operating
condition, because it does not have to be
plugged into an electrical outlet.
Charging (Fig. 2)
1.
Plug the battery charger into your power source. Two charging lights will flash in green color repeatedly.
2.
Insert the battery cartridge into charger until it stops adjusting to the guide of charger. Terminal cover of charger
can be opened with inserting and closed with pulling out the battery cartridge.
3.
When the battery cartridge is inserted, the charging light color will change from green to red and charging will
begin. The charging light will keep lighting up lit steadily during charging. One red charging light indicates charged
condition in 0 – 80% and two red ones indicates 80 – 100%.
4.
With finish of charge, the charging lights will change from two red ones to two green ones.
5.
If you leave the battery cartridge in the charger after the charging cycle is complete, the charger will switch into its
"trickle charge (maintenance charge)" mode which will last approximately 24 hours.
6.
After charging, unplug the charger from the power source.
Battery Type
BH9020A
BH9033A
Conditioning charge
Conditioning charge can extend the life of battery by automatically searching the optimum charging condition for the
batteries in every situation.
The battery employed in the following conditions repeatedly, will be worn out shortly, and yellow warning light may
flash.
1.
Recharge of battery with its high temperature
2.
Recharge of battery with its low temperature
3.
Recharge of full charged battery
4.
Over-discharge of battery (continue to discharge battery in spite of down of power.)
5.
Recharge under broken cooling system
The charging time of such battery is longer than usual.
ENB024-1
Capacity (mAh)
2,000
3,300
2.
Hold tool by insulated gripping surfaces when
performing an operation where the cutting tool
may contact hidden wiring. Contact with a "live"
wire will make exposed metal parts of the tool
"live" and shock the operator.
3.
Always be sure you have a firm footing. Be sure
no one is below when using the tool in high loca-
tions.
4.
Hold the tool firmly.
5.
Wear ear protectors.
SAVE THESE INSTRUCTIONS.
OPERATING INSTRUCTIONS
Installing or removing battery cartridge (Fig. 1)
• Always switch off the tool before insertion or removal of
the battery cartridge.
• To remove the battery cartridge, withdraw it from the
tool while pressing the buttons on both sides of the car-
tridge.
• To insert the battery cartridge, align the tongue on the
battery cartridge with the groove in the housing and slip
it into place. Always insert it all the way until it locks in
place with a little click. If not, it may accidentally fall out
of the tool, causing injury to you or someone around
you.
• Do not use force when inserting the battery cartridge. If
the cartridge does not slide in easily, it is not being
inserted correctly.
Number of cells
8
8
Charging time
Approx. 30 min.
Approx. 50 min.
5
Tabla de contenido
loading

Este manual también es adecuado para:

Btd060

Tabla de contenido