Idiomas disponibles
Idiomas disponibles
DESCRIPTION
The Craftsman
Clipped Head Angle Framing Nailer drives nails
from 113" to 131" diameter and from 2" to 3',_" long
Magazine is angled at 28 ° for nailing in tight spots such as
when toenailing
High strength magnesium body and aluminum
components
are lightweight and durable. Safety feature dis-
ables tco_ unless contact trip is pressed against workpmece
Sequential trigger switch allows selection of ral_d-fire or single-
fire mode Contact tnp can be adjusted for setting nail depth.
Pusher mechanism
supports shorter fasteners to prevent jam-
ming Plastic protector on the end of contact trip prevents mar-
ring of workplace
Large capacity, end loading magazine makes
it easy to load up to 80 stick nails at a time. Tool ddvea straight,
screw, and ring shank nails, Exhaust deflector can be rotated
360 _, The Angle Framing Nailer is excellent for truss maldng,
framing, sheathing, sub-ficodng
and decking.
SPECIFICATIONS
Capacity ....................
75 nails (3Vz"), ao r_ails (2"]
Nail diameter
...........................
113 to 131"
Nail lengths
...............................
2 to 3Vz"
Operating pressure
....................
70 to 110 PSI
Air inlet .................................
'/4" N.F_T
Length .................................
18V."
Height ........................................
14_//'
Width
..........................................
5"
Weight
.....................................
7.3 Ibs.
NAILS
18351
...............
8 penny, ,120" diameter x 2W' tong
18352 ..............
I O penny, .120" diameter x 3" long
18353 ...............
16 penny' . 131" diameter x 3V_"long
GALVANIZED
NAILS
18357 ................
8 penny, .120" diameter x 2'/=" tong
18358 ................
10 penny, .120" diameter x 3" tong
18359 ...............
16 penny,, 131" diameter x 3_/_"long
AIR SUPPLY
LINE
Refer to Figure 1.
DANGER:
Do not use oxygen, carbon dioxide, high-pressure
compressed
gas or bottled gases as the power source for this
tool. The tool will explode and serious personal injury Could
result.
•
]-he air tool operates on compressed
air at pressures from
70 to 110 PSI.
•
Never connect the tool to air pressure which could poten.
tiaPly exceed 200 PSI. Use only clean, dry, regulated air
within rated range as marked on tool.
Air Delivery
Required: 2.21 SCFM @ 90 PSI
(30 shots per minute).
WARNING:
Keep hands and body away from discharge
area
of tool when connecting
air supply. Always disconnect
tool
from air supply when servicing or adjusting tool and when tool
is not in use,
•
Air operated
tools require clean, dry, lubricated
com-
pressed air to ensure top performance,
low maintenance
and tong nfe.
Dirt and abrasive materials
present in all air lines wil! darn
age tool O-rings, valves and cylinders
Moisture will reduce tool performance
and life if not
removed from compressed
air.
•
A filter-regulator-lubricat0r system is required and should be
located as close to teal as possible A distance of less than
15 feet is recommended.
Lubricator is not required for
ailless tools
Keep air filter clean A dirty filter wil! reduce the air pressure
to the tool causing a reduction Jn power and efficiency
The air supply system must be able to provide air pressure
o1 70 to 110 pounds per square inch at toot
•
All hoses and ptpes in the air supply system must be cle_n
and free of moisture and foreign particles
Hoses must be
rated for a maximum working pressure of 150 PSf or 150%
of maximum
system pressure, whichever is greater.
•
Do not mount swivel connector
in air supply lirle
•
The air pressure should be properly regulated,
•
Different workplace
materials
and different fastener lengths
will require different operating pressure
•
Be sure all connections
in air supply system are sealed to
prevent air loss.
•
Never connect a female quick-disconnect
coupling to the
tool side of air line connection. A male, free-flow coupling
should be connected
to the tool side of air fine connection
(.see Figure 1),
WARNING:
The female coupJing provides a seat preventing
loss of compressed air from compressor
tank when discon-
nected from male oaupling
If connected
to tool side of air
supply, the female coupling could seal a compressed
air
charge in the tool which could discharge if the tool trigger is
actuated
LOADING
Refer to Figures 2, 3 & 4, page 4.
WARNING:
Disconnect
tool from air supply, Do not load loot
until you are ready to use it. Do not pull tdgger or depress
contact trip while loading tool, Always load with nose of tool
pothtthg away from you and others, Always wear safety gog-
gles that comply with United States ANSI Z87 1.
NOTE: For best results, use Sears fasteners only.
3
