Milwaukee 5385-59 Manual De Instrucciones página 17

Cat. No. Volts
AC
5385-59 220-240
5385-59A 220-240
5385-59B 127
gRouNDINg
wARNINg
grounding wire can result in the risk of elec-
tric shock. Check with a qualified electrician
if you are in doubt as to whether the outlet
is properly grounded. Do not modify the
plug provided with the tool. Never remove
the grounding prong from the plug. Do not
use the tool if the cord or plug is damaged. If
damaged, have it repaired by a mIlwAukEE
service facility before use. If the plug will not
fit the outlet, have a proper outlet installed by
a qualified electrician.
Grounded Tools: Tools with Three Prong Plugs
Tools marked "Grounding Required" have a three
wire cord and three prong grounding plug. The
plug must be connected to a properly grounded
outlet (See Figure A). If the tool should electrically
malfunction or break down, grounding provides a
low resistance path to carry electricity away from
the user, reducing the risk of electric shock.
The grounding prong in the plug is connected
through the green wire inside the cord to the
grounding system in the tool. The green wire in the
cord must be the only wire connected to the tool's
grounding system and must never be attached to
an electrically "live" terminal. Your tool must
be plugged into an appropriate outlet, prop-
erly installed and grounded in accordance
with all codes and ordinances. The
plug and outlet should look like
those in Figure A.
Double Insulated Tools: Tools
with Two Prong Plugs
Tools marked "Double Insulated" do not require
grounding. They have a special double insulation
system which satisfies OSHA requirements and com-
plies with the applicable standards of
Underwriters Laboratories, Inc., the
Canadian Standard Association and
the National Electrical Code. Double
Insulated tools may be used in ei-
ther of the 120 volt outlets shown in
Figures B and C.
In specific countries, double insulated tools could
be used in the output connections suitable for
the plug.
sPECIfICATIoNs
Tool
W RPM Blows per
650 0 - 1290
650 0 - 1290
650 0 - 1290
Improperly connecting the
Fig. A
Fig. B Fig. C
Twist
Minute Drill Bit
(Wood)
3700 30 mm
3700 30 mm
3700 30 mm
wARNINg
always unplug tool before attaching or remov-
ing accessories or making adjustments. Use
only specifically recommended accessories.
Others may be hazardous.
wARNINg
wear safety goggles or glasses with side shields.
wARNINg
always use a side handle when using this tool.
Always brace or hold securely.
Adjusting the Side Handle Position
1. Loosen the side handle by unscrewing the side
handle grip until the side handle rotates freely.
2. Rotate the side handle to the desired position.
3. Tighten the side handle grip securely.
Setting the Depth Gauge
1. Press in the clamping lever.
2. Slide the depth gauge rod backward or forward
until it is set for the desired depth.
NOTE: The drilling depth is the distance between
the tip of the bit and the tip of the rod.
3. Release the clamping lever.
wARNINg
do not grasp the bit while the chuck is rotat-
ing or while the bit is falling from the chuck.
Installing Drill Bits and Chisels
NOTE: Only use accessories
with SDS or SDS Plus shanks.
Be sure that the shank of the bit is clean. Dirt par-
ticles may cause the bit to line up improperly. Do
not use bits larger than the maximum recommended
capacity of the drill because gear damage or mo-
tor overloading may result. For best performance,
be sure that the bit is properly sharpened and the
shank is lightly greased before use.
1. Insert the bit or chisel into the nose of the tool.
2. Rotate bit slowly until it aligns with the locking
mechanism.
3. Push bit into tool until it locks.
4. Check that the bit is locked properly; it should
be possible to pull the bit back and forth slightly
(about 1/4").
5. To remove bits and chisels, pull bit holder release
collar toward the rear of tool and remove bit.
NOTE: Use caution when handling hot bits and chisels.
17
Capacities
Twist Carbide Tipped
Drill Bit Percussion Bit
(Steel) (concrete)
13 mm 24 mm
13 mm 24 mm
13 mm 24 mm
AssEmbly
To reduce the risk of injury,
To reduce the risk of injury,
To reduce the risk of injury,
To reduce the risk of injury,