Makita 4191D Manual De Instrucciones página 4

ENGLISH
1 Button
2 Battery cartridge
3 Depth guide
4 Clamping screw
5 Base
6 Top of notch
7 Graduation
8 Bevel scale plate
SPECIFICATIONS
Model
Blade diameter ..................................................... 80 mm
Cutting depth
90° ............................................................ 0 – 21.5 mm
45° ............................................................... 0 – 16 mm
-1
No load speed (min ) ........................................... 1,000
Overall length .................................................... 316 mm
Net weight ............................................................. 2.1 kg
Rated voltage ................................................... D.C. 12 V
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications and battery cartridge may differ from
country to country.
• Weight, with battery cartridge, according to EPTA-Pro-
cedure 01/2003
Intended use
The tool is intended for cutting in glass and masonry
materials with a diamond wheel and water.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.
CORDLESS CUTTER SAFETY WARNINGS
1. Read all safety warnings, instructions, illustra-
tions and specifications provided with this
power tool. Failure to follow all instructions listed
below may result in electric shock, fire and/or seri-
ous injury.
2. Always use guard provided with the tool. The
guard must be securely attached to the power
tool and positioned for maximum safety, so the
least amount of wheel is exposed towards the
operator. The guard helps to protect operator from
broken wheel fragments and accidental contact with
wheel.
3. Use only diamond cut-off wheel for your power
tool. Just because the accessory can be attached to
your power tool, it does not assure safe operation.
4. The rated speed of the wheel must be at least
equal to the maximum speed marked on the
power tool. Wheels running faster than their rated
speed can break and fly apart.
5. Always use undamaged wheel flanges that are of
correct diameter for your selected wheel. Proper
wheel flanges support the wheel thus reducing the
possibility of wheel breakage.
4
Explanation of general view
9 Cutting line
10 Lock-off lever
11 Switch trigger
12 Bolt
13 Flange
14 Diamond wheel
15 Hex wrench
16 Shaft lock
6.
4191D
7.
8.
9.
GEB053-2
10. Keep bystanders a safe distance away from work
11. Hold power tool by insulated gripping surfaces
12. Position the cord clear of the spinning wheel. If
13. Never lay the power tool down until the wheel
14. Do not run the power tool while carrying it at
17 Tank holder installing portion
18 Tank
19 Screw (B)
20 Screw (A)
21 Tank holder
22 Cap
The outside diameter and the thickness of your
wheel must be within the capacity rating of your
power tool. Incorrectly sized wheels cannot be ade-
quately guarded or controlled.
The arbour size of wheels and flanges must
properly fit the spindle of the power tool. Wheels
and flanges with arbour holes that do not match the
mounting hardware of the power tool will run out of
balance, vibrate excessively and may cause loss of
control.
Do not use damaged wheels. Before each use,
inspect the wheels for chips and cracks. If power
tool or wheel is dropped, inspect for damage or
install an undamaged wheel. After inspecting
and installing the wheel, position yourself and
bystanders away from the plane of the rotating
wheel and run the power tool at maximum no
load speed for one minute. Damaged wheels will
normally break apart during this test time.
Wear personal protective equipment. Depending
on application, use face shield, safety goggles or safety glasses. As appropriate, wear dust
mask, hearing protectors, gloves and shop
apron capable of stopping small abrasive or
workpiece fragments. The eye protection must be
capable of stopping flying debris generated by vari-
ous operations. The dust mask or respirator must be
capable of filtrating particles generated by your oper-
ation. Prolonged exposure to high intensity noise
may cause hearing loss.
area. Anyone entering the work area must wear
personal protective equipment. Fragments of
workpiece or of a broken wheel may fly away and
cause injury beyond immediate area of operation.
only, when performing an operation where the
wheel may contact hidden wiring. Wheel contact-
ing a "live" wire may make exposed metal parts of
the power tool "live" and give the operator an electric
shock.
you lose control, the cord may be cut or snagged
and your hand or arm may be pulled into the spin-
ning wheel.
has come to a complete stop. The spinning wheel
may grab the surface and pull the power tool out of
your control.
your side. Accidental contact with the spinning
wheel could snag your clothing, pulling the wheel
into your body.