JB Systems Light µ-QUASAR LASER Manual De Instrucciones página 4

ENGLISH
The power cord should always be in perfect condition. Switch the unit immediately off

when the power cord is squashed or damaged. It must be replaced by the manufacturer,
its service agent or similarly qualified persons in order to avoid a hazard.
 Never let the power-cord come into contact with other cables!
In order to avoid a hazard, the unit shall only be used with the AC-adaptor delivered with

it. If the AC-adaptor is damaged, a same model adaptor shall be used only.
Don't connect the unit to any dimmer pack.

Always use an appropriate and certified safety cable when installing the unit.

In order to prevent electric shock, do not open the cover. Apart from the lamp and mains

fuse there are no user serviceable parts inside.
Never repair a fuse or bypass the fuse holder. Always replace a damaged fuse with a

fuse of the same type and electrical specifications!
In the event of serious operating problems, stop using the fixture and contact your dealer

immediately.
The housing and the lenses must be replaced if they are visibly damaged.

Please use the original packing when the device is to be transported.

Due to safety reasons it is prohibited to make unauthorized modifications to the unit.

Important: Never look directly into the light source! Don't use the effect in the presence of
persons suffering from epilepsy.
LASER SAFETY INSTRUCTIONS:
According to the EN/IEC 60825-1 Ed2, 2007-03 regulations, this laser falls under the

classification 3B. Direct eye exposure can be dangerous.
DANGER: LASER RADIATION !
Avoid direct eye exposure! Laser radiation can cause
eye damage and/or skin damage. All protective
measures for a safe operation of this laser must be
This product is a so-called show laser, emitting radiation with a wavelength spectrum

between 400 and 700 nm and producing lighting effects for shows.
Laser Light is different from any other light source with which you may be familiar. The

light from this product can potentially cause eye injury if not set up and used properly.
Laser light is thousands of times more concentrated than light from any other kind of light
source. This concentration of light power can cause instant eye injuries, primarily by
burning the retina (the light sensitive portion at the back of the eye). Even if you cannot
feel "heat" from a laser beam, it can still potentially injure or blind you or your audience.
Even very small amounts of laser light are

potentially hazardous even at
distances.
Never look into the laser aperture or laser

beams
Never direct the laser beam to people or

animals and never leave this device running
unattended.
 This laser may only be used for shows. The
operation of a class 3B show laser is only allowed if the operation is controlled by a
skilled and well-trained operator.
JB SYSTEMS
®
USER MANUAL
applied.
long
3/35 µ-STAR & µ-QUASAR LASER
ENGLISH
Depending on the classification, operating a laser product can produce laser radiation

that may cause permanent eye damage and/or skin damage. The legal instructions for
using a laser product vary from country to country. The user must always inform himself
on the legal instructions valid in his country and apply them to his situation.
The parent document and cornerstone of laser safety standards ANSI Z136.1 (2007)

provides guidance for the safe use of lasers and laser systems by defining control
measures for each of the four laser classes. This valuable document can be obtained
from www.laserinstitute.org
Please note that JB SYSTEMS cannot be made liable for damages caused by incorrect
installations and unskilled operation!
DESCRIPTION:
1. MODE button: Use this button to select one of the 4 modes:

Fast automatic mode (LED is red)

Slow automatic mode (LED is red)

Sound activated (LED is blue)

Sound strobe effect (LED is blue)
Press this button for about 2.5 seconds to turn off the fixture.
2. INTERNAL MICROPHONE: The built-in microphone is used to synchronize the laser
show to the beat of the music. You can set the sensitivity of the microphone via the
wireless remote control.
3. IR RECEIVER: used to control the unit by the wireless remote control.
4. LED INDICATOR: shows you if the laser is in automatic mode (LED is red) or in sound
activated mode (LED is blue).
5. GREEN LASER DIMMER: here you can set the intensity of the green laser if you
would like to change the balance between the red and the green laser.
6. MAINS INPUT: DC12V input. Connect the supplied mains adapter here.
7. COOLING FAN: used to cool the components inside the enclosure. Make sure to
never cover this fan outlet!
JB SYSTEMS
®
USER MANUAL
4/35 µ-STAR & µ-QUASAR LASER