HIKOKI C 8FSHE Instrucciones De Manejo página 11

Gloves for handling saw blades (saw blades shall
be carried in a holder wherever practicable) and
rough material.
15. The operator is adequately trained in the use,
adjustment and operation of the machine.
16. Refrain from removing any cut-offs or other parts
of the workpiece from the cutting area whilst the
machine is running and the saw head is not in the
rest position.
17. Never use the slide compound miter saw with its
lower guard locked in the open position.
18. Ensure that the lower guard moves smoothly.
19. Do not use the saw without guards in position, in
good working order and properly maintained.
20. Use correctly sharpened saw blades. Observe the
maximum speed marked on the saw blade.
21. Do not use saw blades which are damaged or
deformed.
22. Do not use saw blades manufactured from high
speed steel.
23. Use only saw blades recommended by HITACHI.
Use of saw blade comply with EN847-1.
24. The saw blades should be 216 mm external diameter.
25. Select the correct saw blade for the material to be
cut.
26. Never operate the slide compound miter saw with
the saw blade turned upward or to the side.
27. Ensure that the workpiece is free of foreign matter
such as nails.
SPECIFICATIONS
Max. Cutting
Capacity Bevel
Height × Width
Compound
Saw Blade Dimensions (oD × iD × Thickness)
Miter Cutting Angle
Bevel Cutting Angle
Compound Cutting Angle
Voltage (by areas)*
Power Input*
No-Load Speed
Machine Dimensions (Width × Depth × Height)
Weight (Net)
Laser Marker
(Only Model C8FSHE)
* Be sure to check the nameplate on product as it is subject to change by areas.
When cutting the workpiece which has the dimension of "**" there might be some possibility of the lower end of the
circular saw to touch with the workpiece, even if the motor head is located at the lower limit position. Pay attention
when cutting the workpiece. For further details, refer to "PRACTICAL APPLICATIONS". Mount the auxiliary board on
the fence surface (Refer ( ) the thickness of auxiliary board). Refer to "12. Cutting large workpieces" (Fig. 16).
HiKOKI.
0°
Miter 45°
Left 45°
Right 5°
Bevel (Left) 45° + Miter 45°
Bevel (Right) 5° + Miter 45°
Bevel (Left) 0° – 45°
Bevel (Right) 0° – 5°
Maximum output
(Iambda)
Laser medium
28. Replace the table insert when worn.
29. Do not use the saw to cut other than aluminium,
wood or similar materials.
30. Do not use the saw to cut other materials than those
recommended by the manufacturer.
31. Blade replacement procedure, including the method
for repositioning and a warning that this must be
carried out correctly.
32. Connect the slide compound miter saw to a dust
collecting device when sawing wood.
33. Take care when slotting.
34. When transporting or carrying the tool, do not grasp
the holder. Grasp the handle instead of the holder.
35. Start cutting only after motor revolution reaches
maximum speed.
36. Promptly cut OFF the switch when abnormality
observed.
37. Shut off power and wait for saw blade to stop before
servicing or adjusting tool.
38. During a miter or bevel cut the blade should not be
lifted until it has stopped rotation completely.
39. During slide cutting operation, the saw must be
pushed and slided away from the operator.
40. Take all the possibility of residual risks in cutting
operation into your consideration, such as the laser
radiation to your eyes, the inadvertent access to
moving parts on slide mechanical parts on machine
and so on.
65 mm × 312 mm
**75 mm × 262 mm with aux. board (30 mm)
65 mm × 220 mm
**75 mm × 185 mm with aux. board (20 mm)
45 mm × 312 mm
**50 mm × 252 mm with aux. board (30 mm)
60 mm × 312 mm
**70 mm × 252 mm with aux. board (30 mm)
45 mm × 220 mm
**50 mm × 170 mm with aux. board (30 mm)
60 mm × 220 mm
**70 mm × 170 mm with aux. board (30 mm)
216 mm × 25.4 mm × 2 mm
(For Australia: 216 mm × 30 mm × 2 mm)
Right 0° – 57°, Left 0° – 45°
Right 0° – 5°, Left 0° – 48°
Miter (Right and Left) 0° – 45°
(110 V, 220 V, 230 V, 240 V)
555 mm × 790 mm × 485 mm
14.5 kg (C8FSHE) / 14 kg (C8FSE)
Po<3 mW Class
English
1050 W
5500 / min
Laser Product
654 nm
Laser Diode
10