Assembly; Important; Installing The Handle; Installing The Hopper - Echo Bear cat Manual Del Propietário

assembly

2
Section
Warning
Before inspecting or servicing any part of this machine, shut
off power source, disconnect spark plug wire from spark plug
and make sure all moving parts have come to a complete
stop.

imPorTanT

If any bolts or nuts are dropped in the machine, be sure to
remove them before starting the machine. Remove items
from the shredder area by removing the discharge screen.

2.1 inSTalling The handle

modelS: all modelS excePT 70580 & 70580S
1. Remove the chipper/shredder and hopper assembly from
the shipping box and pallet.
2. Install four 5/16" x 3/4" bolts so the head of the bolt is located
on the inside of the hopper. Fasten bolts with 5/16" nylock
nuts and 5/16" flat washers.

2.2 inSTalling The hoPPer

modelS: all modelS
1. Assemble the hopper assembly to the frame so the handle
is located above the engine and the opening is toward the
chipper chute.
2. Install twelve 5/16" x 3/4" bolts so the head of the bolt is
inside the hopper. Fasten bolts with 5/16" flat washers and
5/16" nylock nuts.
2.3 inSTalling The chiPPer chuTe
exTenSion
modelS: all "S" modelS
1. Place the chipper chute extension onto the chute. Line up
the four holes located on the bottom of the extension and
the top of the chute.
2. Install four 5/16" x 3/4" bolts so the head of the bolt is located
on the inside of the chipper chute. Fasten bolts with 5/16"
nuts. Tighten nut until snug against the chute extension.
10
2.4 inSTalling The Wide and narroW
diScharge aSSemblY
modelS: all "S" modelS
1. Place the discharge weldment onto the chipper. The holes on
the weldment should line up with holes on the chipper.
2. secure the top of the discharge weldment using one 5/16" x
7-1/2" bolt (narrow door) or one 5/16" x 10" bolt (wide door)
and 5/16" nuts. Tighten to proper torgue
3. secure the bottom of the discharge weldment using two
5/16" x 3/4" bolts and 5/16" nuts. The head of the bolt should
be located inside the discharge assembly. Tighten to the
proper torque.
2.5 inSTalling The WheelS, jack and
hiTch
modelS: 70580 & 70580S
1. slide one wheel onto a hub and align the wheel lug holes
with the hub lug holes.
2. Thread the wheel bolts into the holes and tighten to the
proper torque. Follow an alternating cross pattern when
tightening wheel bolts.
3. Repeat for the remaining wheel.
4. Install hitch jack onto hitch pole and install snap pin.
5. Align the hitch pole assembly to the frame and secure using
two 3/8" x 2-1/2" bolts, 3/8" flat washers and 3/8" nylock
nuts.

2.6 inSTalling The baTTerY

modelS: 70085 & 70385
The machine may or may not have been shipped with a battery
depending on your area. If you did not receive a battery with your
machine, you will need to purchase one.
use a battery that meets or exceeds the following
specifications:
battery category, lawn and garden
bci group Size u1
200-250 cca
7-3/4" x 5-3/16" x 7-5/16"
Suggested Source:
exide cutting edge, Type gT-h
After purchasing your battery, fill, charge and install the battery
according to the battery owners manual.
3 INCH CHIPPER/SHREDDERS