Additional Safety Rules - Makita 9401 Manual De Instrucciones

ENGLISH
1 Lever
2 Adjusting knob
3 Dust spout
4 Dust bag
SPECIFICATIONS
Model
9401 .........................................100 mm x 610 mm
9402 .........................................100 mm x 610 mm
9900B ......................................... 76 mm x 533 mm
9901 ........................................... 76 mm x 533 mm
9924DB ...................................... 76 mm x 610 mm
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
Safety hints
For your own safety, please refer to the enclosed Safety
instructions.

ADDITIONAL SAFETY RULES

1. Hold tool by insulated gripping surfaces when
performing an operation where the cutting tool
may contact hidden wiring or its own cord. Con-
tact with a "live" wire will make exposed metal parts
of the tool "live" and shock the operator.
2. Hold the tool firmly with both hands.
3. Make sure the belt is not contacting the work-
piece before the switch is turned on.
4. Keep hands away from rotating parts.
5. Do not leave the tool running. Operate the tool
only when hand-held.
6. This tool has not been waterproofed, so do not
use water on the workpiece surface.
7. Ventilate your work area adequately when you
perform sanding operations.
8. Some material contains chemicals which may be
toxic. Take caution to prevent working dust inha-
lation and skin contact. Follow material supplier
safety data.
9. Always use the correct dust mask/respirator for
the material and application you are working
with.
SAVE THESE INSTRUCTIONS.
4
Explanation of general view
5 Switch trigger
6 Lock button
7 Speed change switch
8 Limit mark
Belt size Belt speed
H 350 m/min
L 300 m/min
ENB007-2
9
10 Screwdriver
Overall length
350 m/min
360 m/min
380 m/min
400 m/min
360 m/min (U.K. only)
OPERATING INSTRUCTIONS
Installing or removing abrasive belt (Fig. 1 & 2)
Important:
Always be sure that the tool is switched off and
unplugged before installing or removing the belt.
Pull the lever all the way out and install the belt over the
rollers, then return the lever to the original position.
CAUTION:
When installing the belt, make sure that the direction of
the arrow on the back of the belt corresponds to the one
on the tool itself.
Adjusting belt tracking (Fig. 3)
While the belt is running, use the adjusting knob to center
the belt tracking. Failure to do so can result in frayed belt
edges and wear on the sander frame.
Dust bag (Fig. 4)
The use of the dust bag makes sanding operations clean
and dust collection easy. To attach the dust bag, fit it onto
the dust spout.
For the best results, empty the dust bag when it becomes
about half full, tapping it lightly to remove as much dust
as possible.
Switch action (Fig. 5)
CAUTION:
Before plugging in the tool, always check to see that the
switch trigger actuates properly and returns to the "OFF"
position when released.
To start the tool, simply pull the trigger. Release the trig-
ger to stop. For continuous operation, pull the trigger and
then push in the lock button. To stop the tool from the
locked position, pull the trigger fully, then release it.
Speed change (Fig. 6)
For Model 9402
To change the tool speed, press the "H" side of the speed
change switch for high speed or the "L" side for low
speed.
CAUTION:
Use the speed change switch only after the tool comes to
a complete stop.
Brush holder cap
Net weight
374 mm 7.3 kg
374 mm 7.3 kg
316 mm 4.6 kg
328 mm 3.5 kg
355 mm 4.8 kg