Double Insulation; Additional Safety Rules - Makita 6802BV Manual De Instrucciones

ENGLISH
1 Locking position
2 Locator
3 Locking sleeve
4 Magnetic socket bit
5 Gear housing
SPECIFICATIONS
Capacities
Self drilling screw .......................................... 6 mm
Bit shank size ............................................. 1/4'' Hex
No load speed (RPM) ................................ 0 – 2,500
Overall length ............................................... 265 mm
Net weight ....................................................... 1.7 kg
• Due to the continuing program of research and
development, the specifications herein are subject
to change without prior notice.
• Note: Specifications may differ from country to
country.
Power supply
The machine should be connected only to a power
supply of the same voltage as indicated on the
nameplate, and can only be operated on single-phase
AC supply. They are double-insulated in accordance
with European Standard and can, therefore, also be
used from sockets without earth wire.
Safety hints
For your own safety, please refer to enclosed safety
instructions.
These symbols mean:
Read instruction manual.

DOUBLE INSULATION

ADDITIONAL SAFETY RULES

1. Always be sure you have a firm footing.
Be sure no one is below when using the
machine in high locations.
2. Hold the machine firmly.
3. Keep hands away from rotating parts.
4. When driving into walls, floors or wherever
''live'' electrical wires may be encountered, DO
NOT TOUCH ANY METAL PARTS OF THE
MACHINE!
Hold the machine by the insulated grasping
surfaces to prevent electric shock if you drive
into a ''live'' wire.
5. Do not touch the bit or the workpiece immedi-
ately after operation; they may be extremely
hot and could burn your skin.
SAVE THESE INSTRUCTIONS.
Explanation of general view
6 Socket bit
7 Low
8 High
9 Speed control screw
0 Switch trigger
OPERATING INSTRUCTIONS
Removing or installing locator assembly
(Fig. 1)
To remove the locator assembly, pull the locking
sleeve forward and then turn it counterclockwise. To
install the locator assembly, screw it clockwise and
then push the locking sleeve back in lightly toward the
motor. Turn the locking sleeve slightly to match the
locking positions and then push in firmly to lock the
locator in place.
Removing or installing magnetic socket bit
(Fig. 2)
Important:
Always be sure that the machine is switched off and
unplugged before removing or installing the bit.
After removing the locator assembly, pull firmly to
remove the magnetic socket bit. To install the bit,
insert it into the machine as far as it will go.
Depth adjustment (Fig. 3 & 4)
Pull the locking sleeve forward and then turn it to
adjust the depth.
Initially, adjust the locator assembly to create a dis-
tance of approximately 0.5 mm from the tip of the
locator to the tip of the socket bit. One full turn of the
locator equals 1.5 mm change in depth. After adjust-
ing the locator assembly, push the locking sleeve in to
lock the locator in place. Drive a trial screw into your
material or a piece of duplicate material. If the depth
is not suitable for the screw, continue adjusting until
the proper depth setting is obtained.
Switch action (Fig. 5)
CAUTION:
Before plugging in the machine, always check to see
that the switch trigger actuates properly and returns to
the ''OFF'' position when released.
To start the machine, simply pull the trigger. Machine
speed is increased by increasing pressure on the
trigger. Release the trigger to stop. For continuous
operation, pull the trigger and then push in the lock
button. To stop the machine from the locked position,
pull the trigger fully, then release it. A speed control
screw is provided so that maximum machine speed
can be limited (variable). Turn the speed control
screw clockwise for higher speed, and counterclock-
wise for lower speed.
NOTE:
Even with the switch on and motor running, the bit will
not rotate until you fit the point of the bit in the screw
head and apply forward pressure to engage the
clutch.
q Lock button
w Reversing switch lever
e Insert bit
r Magnetic bit holder
3