Technical Data; Before Starting The Equipment - EINHELL BT-BD 701 Manual De Instrucciones

Anleitung_BT_BD_701_SPK7:_
GB

5. Technical data

Nominal input voltage
Power rating
Operating mode
Motor speed
Output speed
Speed levels
Drill chuck mount
Scroll chuck
Max. shaft diameter
Reach
Dimensions of drill table
Angle adjustment of table
Drill depth
Pillar diameter
Height
Base area
Weight
L sound pressure level
pA
L sound power level
WA
K uncertainty
pA
K uncertainty
WA
Sound and vibration
Sound and vibration values were measured in
accordance with EN 61029.
Load factor:
A load factor of S2 15 min (intermittent periodic duty)
means that you may operate the motor continuously
at its nominal power level (630 W) for no longer than
the time stipulated on the specifications label (15
minutes ON period). If you fail to observe this time
limit the motor will overheat. During the OFF period
the motor will cool again to its starting temperature.
Warning!
The specified vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equipment
is used and may exceed the specified value in
exceptional circumstances.
The specified vibration value can be used to compare
the equipment with other electric power tools.
The specified vibration value can be used for initial
assessment of a harmful effect.
14
07.02.2011 14:44 Uhr Seite 14
Keep the noise emissions and vibrations to a
minimum.
Only use appliances which are in perfect working
230V ~ 50 Hz
order.
630 W
Service and clean the appliance regularly.
S2 15 min.
Adapt your working style to suit the appliance.
1,400 rpm
Do not overload the appliance.
240 – 2,520 rpm Have the appliance serviced whenever
necessary.
12
Switch the appliance off when it is not in use.
B 16
Wear protective gloves.
Ø 1.5 - 16 mm
16 mm
Residual risks
126 mm
Even if you use this electric power tool in
200 x 195 mm
accordance with instructions, certain residual
45° / 0° / 45° risks cannot be rules out. The following hazards
may arise in connection with the equipment's
60 mm
construction and layout:
60 mm
1. Lung damage if no suitable protective dust mask
approx. 850 mm
is used.
350 x 230 mm
2. Damage to hearing if no suitable ear protection is
33.5 kg
used.
74 dB(A)
3. Health damage caused by hand-arm vibrations if
87 dB(A) the equipment is used over a prolonged period or
is not properly guided and maintained.
3 dB
3 dB

6. Before starting the equipment

6.1. Installing the machine (Fig. 1/3/4)
Place the base plate (1) in the desired position.
Fasten the pillar (2) with flange using the supplied
screws (3).
Insert the screw gear in the drill table support.
Then insert the gear rack (30) in the drill table
support (5) with the teeth facing the screw gear
(identical projection).
Now slip these parts together over the pillar (2). In
doing so, make sure that the gear rack is correctly
seated in the teeth of the screw gear.
To secure the gear rack at the top end, slip on the
guide sleeve (29) over the pillar and fasten with
the screw.
You can now fit the table and clamp in place with
the clamping lever. Following this, fit the crank
(27) and fasten tightly with the screw (28).
Finally, fit the complete bit head to the pillar. Align
the head so that it is horizontal to the base plate
and fasten it in position with the screws (35).
Screw the 3 supplied handles (9) in the handle
mounts.
Before you mount the drill chuck with the MK
shank, check that both parts are clean. Insert the
taper mandrel in the taper of the drill chuck with a
powerful jolt. Then insert the taper in the spindle
(Fig. 12)