Continuous Operation - EINHELL TE-BS 8540 E Manual De Instrucciones Original

You can then connect a suitable dust extractor (a)
to the dust extractor adapter (15) (dust extractor
not supplied).
This will provide excellent dust extraction on the
workpiece.
Check that all the parts are properly connected.
Important. The vacuum cleaner you use for the
extraction work must be suitable for the workpie-
ce material.
5.1.2 Installing the dust collection box
(Figure 4/Item 14)
Push the dust collection box (14) to the dust ext-
ractor connection (6). Remove the dust collection
box in reverse order.
The dust is extracted directly via the grinding/san-
ding belt into the dust container.
Important.
For health safety reasons it is imperative that you
use a dust container or a dust extraction system
via the dust extraction adaptor!
5.2 Adjusting the additional handle
(Fig. 5/Item 2)
Slacken the screw (1) and move the additional
handle (2) to its optimal position. Lock the additio-
nal handle (2) in place by tightening the screw (1).
5.3 Changing the sanding / grinding belt
(Fig. 6-7/Item 13)
•
Pull the clamping lever (12) to the outside to
relieve the tension in the sanding/grinding
belt.
•
Pull the used sanding/grinding belt off the
drive rollers.
•
Slide the new sanding/grinding belt on to the
drive rollers.
•
Ensure that the direction of the sanding/grin-
ding belt (arrows on the inside of the sanding/
grinding belt) is identical to the direction of
the belt sander/grinder (arrow over the rear
drive roller).
•
Press the clamping lever (12) to the rear to
tension the sanding/grinding belt.
5.4 Adjusting the position of the belt
(Fig. 8/Item 8)
•
Hold the belt sander/grinder with the sanding/
grinding plate at the top.
•
Switch on the belt sander/grinder.
•
By turning the setting screw (8) the belt positi-
on should be set so that the sanding/grinding
Anl_TE_BS_8540_E_SPK9.indb 18 Anl_TE_BS_8540_E_SPK9.indb 18
GB
belt is at the center of the two drive rollers.
5.5 Moving sanding/grinding belt cover
(Fig. 9 – 10/Item 9)
Important.
The moving sanding/grinding belt cover may only
be swung upwards if the pushbutton (7) has been
pressed.
•
Press the pushbutton (7) and at the same
time swing the cover (9) upwards.
•
Release the pushbutton.
•
The cover will lock in its end position.
•
To swing the cover back down again, press
the pushbutton (7) again. The cover can then
be swung downwards.
6. Starting up
6.1 Switching ON/OFF (Fig. 11)
To switch on:
Press the ON/OFF switch (5).

Continuous operation:

Secure the switch (5) with the locking button (4).
To switch off :
Press the ON/OFF switch (5) briefl y.
The machine can be operated on a temporary or
permanent setting.
6.2 Setting the belt speed (Fig. 12/Item 3)
You can select the belt speed by turning the set-
ting knob (3).
PLUS direction:
Increase belt speed
MINUS direction:
Reduce belt speed
6.3 Instructions for use
Warning! Never hold the workpiece you wish to
sand/grind in your hands. Secure the workpiece
on a sturdy surface or using a vise.
•
Allow the belt sander/grinder to start before
you place it on the workpiece.
•
Do not switch off the belt sander/grinder as
long as the sanding/grinding belt is in contact
with the workpiece.
•
Always hold the belt sander/grinder with both
hands whilst it is in use.
- 18 -
07.11.2019 08:07:37 07.11.2019 08:07:37