Transportation And Storage; Cleaning And Maintenance; Installing The Appliance - STAMOS S-LP-2B Manual De Instrucciones

10. WARNING - RISK OF SERIOUS INJURY OR DEATH! Never submerge the device in water or other
liquid when cleaning or using. Never put the device under running water or other liquids. Do not pour
or transfer liquids between containers above the lamp. If liquid of any type penetrates to the inside of
the lamp, immediately remove the plug from the electricity socket and contact an electrician.
11. Open the housing under no circumstances.
12. WARNING - FIRE RISK! If the magnifying glass is used incorrectly, it may focus a beam of light onto a
small area, which in turn will generate a very high temperature!
13. Do not look directly at the light source with the lamp switched on. Do not use the magnifying glass to
look at other light sources (e.g. LED diodes, laser, etc.) - this may damage your eyesight!
14. Do not leave the device or its packaging unsupervised.
TECHNISCHE DETAILS
Product name Magnifying Lamp
Model S-LP-2B
Art. No 6141
Rated voltage [V] / 230~V±10% / 50Hz
Frequency [Hz]
Light source LED diodes – 40 pcs
Magnifying glass diameter 90
[mm]
Magnifying glass 5x / 10x
Power W 1
Dimensions of base (L x 125x200
W) mm
SCOPE OF APPLICATION
The magnifying lamp is designed for direct observation of small items from a short distance.
The user is liable for any damage resulting from non-intended use of the device!
BEFORE FIRST USE
Upon receipt of the goods, check the packaging for integrity and open it. If the packaging is damaged,
please contact your transport company and distributor within 3 days, and document the damages as
detailed as possible. Do not turn the package upside down! When transporting the package, please
ensure that it is kept horizontal and stable.
DISPOSING OF PACKAGING
Please keep all packaging materials (cardboard, plastic tapes and Styrofoam), so that in case of a problem,
the device can be sent back to the service centre in accurate condition.

INSTALLING THE APPLIANCE

Appliance location
The temperature of environment must not be higher than 45 °C and the relative humidity should be less
than 85%. Ensure good ventilation in the room in which the device is used. The distance from any wall
of the device should be not less than 10 cm. Operate the device on flat, stable, clean, refractory and dry
surfaces out of the reach of children and people with mental disabilities. Install the device making sure
that constant access to the main plug is ensured. The power cord connected to the appliance must be
properly grounded and correspond to the technical details. Before first use, remove all elements and
clean them along with the entire device.
8
EN
Magnifying Lamp Magnifying Lamp
S-LP-3S S-LP-4G
6142 6143
230~V±10% / 50Hz 230~V±10% / 50Hz
LED diodes – 40 pcs LED diodes – 40 pcs
90 90
5x / 10x 5x / 10x
1 1
125x200 125x200
Rev. 28.11.2016
PRINCIPLE OF OPERATION
2
1
3
1.
2.
3.
7
4
4.
5
5.
6.
6
7.
ASSEMBLY / USE OF THE DEVICE'S ELEMENTS:
Ensure the power cable does not constitute an obstacle for those in the vicinity. Connect the plug to an
electricity socket. Turn the lamp on using the main switch in the base of the lamp.
Only for 6142 S-LP 3S: There are two magnetic elements on the bottom base of the lamp which may be
used to keep items in place.

TRANSPORTATION AND STORAGE

Shaking, crashing and turning upside down of the device should be prevented when transporting it. Store
it in a properly ventilated location with dry air and without any corrosive gas.

CLEANING AND MAINTENANCE

• Disconnect from electricity when cleaning equipment.
• Use cleaner without corrosive substances to clean surface.
• Dry all parts well after cleaning before the device is used again.
• Store the unit in a dry, cool location, free from moisture and direct exposure to sunlight.
REGULAR CONTROL OF THE DEVICE
Regularly control whether the device is damaged. If it should be damaged, please stop using it immediately
and contact your customer service to solve the problem.
What to do in case of a problem?
Please contact your customer service and prepare the following information:
•
Invoice number and serial number (the latter is to be found on the technical plate on the device).
• If relevant, a picture of the damaged, broken or defective part.
•
It will be easier for your customer service clerk to determine the source of the problem if you give a
detailed and precise description of the matter. Avoid ambiguous formulations like "the device does not
heat", which may mean either that it does not heat enough or that it does not heat at all. The more
detailed your information, the better the customer service will be able to solve your problem rapidly
and efficiently!
CAUTION: Never open the device without the authorization of your customer service. This can lead to
a loss of warranty!
Rev. 28.11.2016
EN DE
LED lighting
opening magnifying glass cover
adjustable arm
ON/OFF switch
magnetic elements(only for 6142 S-LP 3S)
base
power cable
9