Milwaukee 6065 Manual Del Operador página 7

Installing Sanding Discs
1. Unplug tool and place it upside down on a level surface as shown. Remove any accessories from spindle.
2. Thread fl ange and nylon washer onto spindle. Attach backing pad and sanding disc using Fig. 2 to determine type and order of assembly.
NOTE: When installing fl ap disc without hub, position fl ap disc nut as shown.
3. To tighten, press in the spindle lock button while turning disc nut clockwise.
4. To remove sanding disc and backing pad, unplug tool and reverse procedure.
Fig. 2
Disc nut
Sanding
disc
A
Backing
pads
A. Polypropylene
B. Spiral
C. Rubber
D. Phenolic
Sanding
1. Use a clamp, vise or other practical means to hold your work, freeing
both hands to control your tool. Firmly grasp rear handle and side handle
before starting and while tool is in operation. Allow sanding disc to come
to full speed before beginning to sand.
2. Hold tool at 5° to 15° angle as shown to ensure proper sanding pressure
and control (Fig. 3). Too great an angle will result in too much pressure
and could cause excessive wear to the disc and workpiece. Too small
an angle will reduce control.
Fig. 3
For best results, use only
this portion of the disc.
3. Use long, sweeping, side to side strokes, advancing forward to produce
the desired fi nish.
Removing Welds or Hammer Marks
When removing welds or hammer marks, limit coarse sanding to the im-
mediate area. Use successively fi ner grits to smooth surface.
Cross Sanding
When fi nishing a surface that has been prepared by a coarse disc or
wheel, sand at right angles to the strokes made by the coarser disc.
Finishing marks left from previous sanding are easily seen and removed for
a uniform fi nish. Failure to cross sand when changing from a coarse disc to
a fi nishing disc may result in deep scratches and circular marks.
USING SANDING DISCS
B C
Hold at a 5° to 15° angle
D
Nylon washer
Flange
Spindle
Spindle lock button
Finishing Metal
Constantly move across the surface. Work faster on curved surfaces where
contact areas are smaller and pressure is greater. Flat areas may appear
at the end of the stroke when pressure is too heavy. Ease up on pressure
at end of each stroke and when reversing strokes.
Troubleshooting
Deep scratches and circular marks can result from:
• Using too coarse a grit
• Using a partially glazed disc
• Dirt or loose metal on the workpiece
• Failure to sand across the grain when changing from coarse to
fi nishing discs
Bluish discoloration of metal surface indicates:
• Excessive heat caused by circular motion in a small area
• Excessive pressure
• Use of worn out or glazed discs
Selecting Sanding Discs & Grit
Refer to the table below to select the correct type of sanding disc for your
job. Generally, use 16, 24 or 36 grit for heavy stock removal; 50, 60 or 80
grit for medium stock removal and 120 grit for fi nishing. Always begin with
a coarse grit, using successively fi ner grits to obtain the desired fi nish. See
Catalog for a complete list of MILWAUKEE sanding discs.
Aluminum
Oxide
F o r f a s t c u t t i n g ,
general purpose discs
for most metal jobs.
Best for cold-rolled
steel, stainless steel or
metals requiring tough,
fast cutting, long last-
ing abrasives.
Flap disc nut
position
Flap disk
without hub
Rubber
Type 27
pad
fl ange
Aluminum
Zirconia Bi-Cut
Unique grit pattern is Lasts up to 3 times
a r r a n g e d i n c l u s - longer than aluminum
ters for faster stock oxide discs. For general
removal and cleaning. metal working. Ideal for
Ideal for removing paint tough jobs.
from cars, boats, etc.
without clogging.
Flap disk
with hub
Ceramic
page 7