Tabla de contenido
Anleitung_KS_210_2_Profi_SPK7:_
GB
5. Technical data
Asynchronous motor
Input power
Operating mode
Idle speed n
0
Carbide saw blade
Number of teeth
Weight
Tilting range
Mitre cuts
Sawing width at 90°
Sawing width at 45°
Sawing width at 2 x 45°
(double mitre cuts)
Sound and vibration
Sound and vibration values were measured in
accordance with EN 61029.
L
sound pressure level
pA
K
uncertainty
pA
L
sound power level
WA
K
uncertainty
WA
Vibration emission value a
< 2.5 m/s
h
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Keep the noise emissions and vibrations to a
minimum.
Only use appliances which are in perfect working
order.
Service and clean the appliance regularly.
Adapt your working style to suit the appliance.
Do not overload the appliance.
Have the appliance serviced whenever
necessary.
Switch the appliance off when it is not in use.
Wear protective gloves.
12
03.09.2010
10:58 Uhr
6. Before putting the machine into
operation
230 V ~ 50 Hz
The machine has to be set up in a stable
1200 W
position, i.e. it has to be bolted to a workbench, a
S1
universal stand or the like.
All the covers and safety devices have to be
5000 rpm
properly fitted before the machine is switched on.
ø210 x ø30 x 2,5 mm
It must be possible for the saw blade to run
24
freely.
When working with wood that has been
8,8 kg
processed before, watch out for foreign bodies
-45° / 0° / +45°
such as nails or screws etc.
0° to 45° to the left
Before you actuate the On/Off switch, make sure
that the saw blade is correctly fitted and that the
max. 120 x 60 mm
machineʼs moving parts run smoothly.
max. 80 x 65 mm
Before you connect the machine to the power
supply, make sure the data on the rating plate is
the same as that for your mains.
80 x 35 mm
6.1 Setting up the saw (Fig. 12)
Screw the additional stability bar (32) to the back
of the machine.
6.2 Adjusting the saw (Fig. 1/2)
To adjust the turntable (8), loosen the locking
grip (10) by approx. 2 turns, which frees the
Operating
turntable (8).
The turntable (8) has locking points at angles of
94,2 dB(A)
0°, 15°, 22,5°, 30° and 45°. Once the turntable
3 dB
(8) is engaged, the setting must be additionally
107,2 dB(A)
secured by tightening the locking grip (10).
3 dB
If you need to work with any other angles, the
rotary table is fixed in position with just the
2
locking handle (10).
Lightly press the machine head (4) down while at
the same time pulling the retaining pin (16) out
from the motor mounting; this causes the saw to
move down to the lower working position.
Swing up the machine head (4).
By loosening the lock screw (12), the machine
head (4) can be angled to the left up to 45°.
Check that the voltage marked on the rating
plate is the same as your mains voltage and
connect up the machine.
6.3 Precision adjustment of the stop rail (Fig. 5/6)
Lower the machine head (4) and fasten in place
with the safety pin (16).
Fasten the turntable (8) in 0° position.
Place the 90° stop angle (a) between the blade
(5) and the stop rail (7).
Slacken the adjustment screws (28), set the stop
rail (7) to 90° in relation to the saw blade (5) and
retighten the adjustment screws (28).
Seite 12
Tabla de contenido
