Technical Data - ALPHA-TOOLS TK 1500 E Manual De Instrucciones

Anleitung TK 1500 E_SPK7
GB
Wear a breathing mask
Noise emission values
Idle
Sound pressure level LPA 100,6 dB(A) 87,5 dB(A)
Sound power level LWA 112,6 dB(A) 101,1 dB(A)
The quoted values are emission values and not
necessarily reliable workplace values. Although there
is a correlation between emission and immission
levels it is impossible to draw any certain conclusions
as to the need for additional precautions. Factors
with a potential influence on the actual immission
level at the workplace include the duration of impact,
the type of room, and other sources of noise etc.,
e.g. the number of machines and other neighboring
operations. Reliable workplace values may also vary
from country to country. With this information the
user should at least be able to make a better
assessment of the dangers and risks involved.

5. Technical data

AC motor 230V
Power P S1 1200 W S6 40% 1500 W
Idle speed n
0
Cutting-off wheel Ø 250 x Ø 30 x Ø 2.4 mm
Number of teeth
Table size 640 x 446 mm
Cutting height max.
Height adjustment infinite 0 -75 mm
Tilting saw blade infinite 0° - 45°
Extractor socket
Operating mode S6 40%: Continuous operation with
idling (cycle time 10 minutes). To ensure that the
motor does not become excessively hot it may only
be operated for 40% of the cycle at the specified
rating and must then be allowed to idle for 60% of
the cycle.
20
18.08.2006 9:33 Uhr
6. Before putting the machine into
operation
Unpack the bench-type circular saw and check it
for damage which may have occurred in transit.
The machine has to be set up where it can stand
firmly, e.g. on a work bench, or it must be bolted
to a strong base.
All covers and safety devices have to be
mode
properly fitted before the machine is switched
on.
It must be possible for the saw blade to run
freely.
When working with wood that has been
processed before, watch out for foreign bodies
such as nails or screws etc.
Before you actuate the On/Off switch, make sure
that the saw blade is correctly fitted and that the
machine's moving parts run smoothly.
Before you connect the machine to the power
supply, make sure the data on the rating plate is
the same as that for your mains.
7. Assembly
Important! Pull out the power plug before
carrying out any maintenance, resetting or
assembly work on the cutting-off machine!
7.1 Assembling the base frame (Fig. 15/16/17)
50Hz
Turn the saw upside down and place it on the
floor.
Use the washers (b) and the hex screws (a) to
5700 min -1
fasten the 4 legs (29) loosely to the saw.
Now use the hex screws (a), the washers (b)
and the nuts (c) to fasten the longitudinal struts
24
(31) and the cross-struts (30) loosely to the legs.
Please note: The longer struts have to be used
on the sides.
75 mm / 90°
Finally, tighten all screws and nuts on the base
frame.
48 mm / 45°
7.2 Fitting / removing the saw blade guard (Fig. 3)
Mount the saw blade guard (2) on the splitter (5)
so that the screw fits through the hole (18) in the
Ø 35 mm
splitter.
Do not tighten the screw (15) too far – the blade
guard must be able to move freely.
Fasten the extractor hose (13) to the extractor
adapter (16) and to the extractor socket of the
blade guard (2).
A suitable extractor system has to be connected
to the outlet of the extractor adapter (16).
To remove the saw blade guard, proceed in
Seite 20