Technical Data; Safety Instructions; Mains Connection - AEG SBE 500 R Instrucciones De Uso

TECHNICAL DATA

Nominal power output ...................................
Rated output ..................................................
No-load speed ...............................................
1st gear ......................................................
2nd gear .....................................................
Speed under load max. .................................
1st gear ......................................................
2nd gear .....................................................
Percussion rate .............................................
Rate of percussion under load max. ..............
Static jamming moment*, 1st gear/2nd gear .
Drilling capacity in concrete ...........................
Drilling capacity in brick and tile ....................
Drilling capacity in steel .................................
Drilling capacity in aluminium ........................
Drilling capacity in wood ................................
Drill opening range ........................................
Drive shank ...................................................
Chuck neck diameter .....................................
Weight without cable .....................................
Typical weighted acceleration in the hand-
arm area ........................................................
Typical A-weighted sound levels:
Sound pressure level .....................................
Sound power level .........................................
Wear ear protectors! Measured values determined according to EN 50 144.
The data stated above apply for models with 230 - 240 V.
In case of deviating mains voltage, the data stated on the rating plate are applicable.
* Measured according to AEG norm N 877318

SAFETY INSTRUCTIONS

Please pay attention to the safety instructions in the attached
leaflet!
Appliances used at many different locations including open air
must be connected via a current surge preventing switch.
Always wear goggles when using the machine. It is
recommended to wear gloves, sturdy non slipping shoes and
apron.
Sawdust and splinters must not be removed while the
machine is running.
Always disconnect the plug from the socket before carrying
out any work on the machine.
Only plug-in when machine is switched off.
Keep mains lead clear from working range of the machine.
Always lead the cable away behind you.
Always use the auxiliary handle, even if the machine has a
safety clutch since this safety clutch only engages when the
machine blocks with a jerk.
Do not use diamond core drills on hammer mode.
When working in walls ceiling, or floor, take care to avoid
electric cables and gas or waterpipes.
SPECIFIED CONDITIONS OF USE
The electronic drill/screwdriver can be universally used for
drilling, percussion drilling, screwdriving and cutting screw
threads.
Do not use this product in any other way as stated for normal
use.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product is in
conformity with the following standards or standardized
documents. EN 50144, EN 55014-1, EN 55014-2, EN 61000-
3-2, EN 61000-3-3, in accordance with the regulations 98/37/
EC, 89/336/EEC
Manager Product Development
SBE 500 R SBE 550 R
........500 W .........550 W ............. 570 W .............. 600 W .............. 630 W ........... 550 W ...........570 W ..........630 W
........250 W .........275 W ............. 285 W .............. 300 W .............. 315 W ........... 275 W ...........285 W ..........315 W
0-2650 .. min 0-2700 min
-1
.............- ..................- ..................... - ....................... - ...................... - ............. 2200 min
.............- ..................- ..................... - ....................... - ...................... - ............. 2700 min
......1800 min ...1700 min
-1
.............- ..................- ..................... - ....................... - ...................... - ............... 950 min
.............- ..................- ..................... - ....................... - ...................... - ............. 1700 min
... 39750 min .40500 min
-1
... 27000 min .25500 min
-1
..........21 Nm .........21 Nm ............ 23 Nm .............. 21 Nm .............. 21 Nm ...... 25/24 Nm ......25/24 Nm .....25/24 Nm
..........13 mm .........13 mm ............ 15 mm .............. 15 mm ............. 15 mm ............13 mm ...........13 mm ......... 13 mm
..........15 mm .........15 mm ............ 18 mm .............. 18 mm ............. 18 mm ............15 mm ...........15 mm ......... 15 mm
..........10 mm .........10 mm ............ 13 mm .............. 13 mm ............. 13 mm ............10 mm ...........10 mm ......... 13 mm
..........10 mm .........13 mm ............ 13 mm .............. 13 mm ............. 13 mm ............10 mm ...........10 mm ......... 13 mm
..........20 mm .........20 mm ............ 30 mm .............. 30 mm ............. 30 mm ............20 mm ...........20 mm ......... 30 mm
... 1,0-10 mm ...1,5-13 mm ......1,5-13 mm ........1,5-13 mm .......1,5-13 mm ..... 1,0-10 mm .... 1,0-10 mm ...1,5-13 mm
. 1/2"x20 .......1/2"x20 ..........1/2"x20 ............1/2"x20 ...........1/2"x20 ......... 1/2"x20 ........ 1/2"x20 ........1/2"x20
..........43 mm .........43 mm ............ 43 mm .............. 43 mm ............. 43 mm ............43 mm ...........43 mm ......... 43 mm
.........1,6 kg ..........1,6 kg ............. 1,7 kg ............... 1,7 kg .............. 1,7 kg .............1,7 kg ............1,7 kg ........... 1,7 kg
..........18 m/s ........18 m/s
2
.......100 dB (A) .100 dB (A) .....100 dB (A) ......100 dB (A) ......100 dB (A) ... 100 dB (A) ... 100 dB (A) .. 100 dB (A)
....... 113 dB (A) .113 dB (A) .....113 dB (A) ...... 113 dB (A) ......113 dB (A) ....113 dB (A) ... 113 dB (A) ...113 dB (A)
Volker Siegle
SBE 570 R SBE 600 R
...0-2700 min .....0-2800 min ....0-2800 min
-1 -1 -1
...... 1600 min ........1300 min ....... 1300 min
-1 -1 -1
....40500 min ......42000 min ..... 42000 min
-1 -1 -1
....24000 min ......19500 min ..... 19500 min
-1 -1 -1
........... 18 m/s ............. 18 m/s ............ 18 m/s
2 2 2

MAINS CONNECTION

Connect only to single-phase a.c. current and only to the
system voltage indicated on the rating plate. It is also possible
to connect to sockets without an earthing contact as the
design conforms to safety class II.
MAINTENANCE
The ventilation slots of the machine must be kept clear at all
times.
If the machine is mainly used for percussion drilling, regularly
remove collected dust from the chuck. To remove the dust
hold the machine with the chuck facing down vertically, and
completely open and close the chuck. The collected dust will
fall from the chuck. It is recommended to regularly use
cleaner for the clamping jaws and the clamping jaw borings.
Use only AEG accessories and spare parts. Should
components need to be exchanged which have not been
described, please contact one of our AEG service agents (see
our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered.
Please state the ten-digit No. as well as the machine type
printed on the label and order the drawing at your local
service agents or directly at: AEG Elektrowerkzeuge,
Max-Eyth-Straße 10, D-71364 Winnenden, Germany.
SYMBOLS
Always disconnect the plug from the socket
before carrying out any work on the machine.
Accessory - Not included in standard
equipment, available as an accessory.
SBE 630 R SB2-550 SB2-570
-1
.....2200 min
-1
.....2700 min
-1
-1
.......920 min
-1
.....1600 min
-1
... 39750 min .. 39750 min
-1 -1
... 25500 min .. 24000 min
-1 -1
...........18 m/s ..........18 m/s
2 2
ENGLISH
SB2-630
....2250 min
-1 -1
....2800 min
-1 -1
......850 min
-1 -1
....1300 min
-1 -1
..42000 min
-1 -1
..19500 min
-1 -1
........ 18 m/s
2 2
16