Additional Functions; Display Blanking; Colour Balance / White Balance; Key Lock - IMG STAGELINE PARL-174 DMX Manual De Instrucciones

GB
4) Set the desired sub-address with the button
or .
5) Press the button MENU / ESC to return to the
main menu; the display shows
6) Select the menu item
and press ENTER to confirm.
7) Select the submenu item
or and press ENTER to confirm.
8) If the display shows
has been deactivated, activate it with the button
( ).
9) Adjust the spotlight for control via 8 DMX chan-
nels chapter 8.2 (menu item
).
In order to operate the spotlight, set DMX channel 8
on the light controller to the DMX value correspond -
ing to the sub-address of the spotlight (
chapter 10.1.5).
9

Additional Functions

9.1 Display blanking

If you prefer the display (3) to be blank during oper-
ation, activate the automatic display blanking:
1) Press the button MENU / ESC repeatedly until
you enter the main menu.
2) Select the option
button or
3) Select the submenu item
or and press ENTER to confirm.
4) If the display shows
has been deactivated, i. e. the display is always
on. When the display blanking has been acti-
vated (
seconds after the last button was pressed; it is
switched on again when a button is pressed.
Select the desired option with the button

9.2 Colour balance / white balance

It is possible to shift the balance between the three
primary colours red, green and blue. This will also
change the light colour for combined white light (if
the three colours are used in addition to the white
LEDs), e. g. to balance differences to other spot-
lights if the LED spotlight is controlled together with
them.
To activate the colour balance function and to set
the correction values:
1) Press the button MENU / ESC repeatedly until
you enter the main menu.
16
with the button
with the button
, i. e. sub-addressing
in the main menu with the
and press ENTER to confirm
with the button
, the display blanking
), the display is switched off a few
2) Select the option
button
3) Select the submenu item
again.
or
4) If the display shows
tivated, i. e. the correction values adjusted are
not taken into account. Activate the function with
the button
5) Press the button MENU / ESC to return to the
main menu; the display only shows
6) Select the menu item
7) Press the button ENTER. The display shows the
, setting
last primary colour adjusted, red ( ), green ( )
or blue ( ) and the corresponding correction
value (0 – 255). This is the maximum brightness
to be set for this colour.
ID table,
8) Set the value for the colour selected with the but-
ton
9) To switch between the colours, press the button
ENTER.

9.3 Key lock

To prevent accidental operation, a key lock can be
activated.
Activating the key lock:
1) Press the button MENU / ESC repeatedly until
you enter the main menu.
2) Select the option
button
3) Select the submenu item
or
4) The display shows
deactivated. Activate the function (
the button
no longer possible to operate the spotlight via
the buttons MENU / ESC,
or .
Deactivating the key lock
1) Press the button ENTER twice.
2) Press the buttons in the following sequence:
→ → → . Each time you press a button,
a horizontal line appears on the display.
3) Press the button ENTER to terminate the input.
4) Deactivate the key lock function within approx. 8
seconds with the button
wait too long, the key lock is activated again. In
this case, repeat the steps above.
Note: When the key lock is activated and the power sup-
ply is switched off and on again, the last operating mode
selected will not automatically be continued.
in the main menu with the
or and press ENTER to confirm.
and press ENTER to confirm.
, the function is deac-
or
(
).
or .
in the main menu with the
or and press ENTER to confirm.
and press ENTER to confirm.
, i. e. the key lock is
or . After approx. 10 seconds it is
with the button
again.
with the button .
with the button
) with
and .
or ( ). If you