Adjusting The Start Address; Control With The Led-4C; Further Functions; Indication Of Temperature - IMG STAGELINE PARL-7DMX Manual De Instrucciones

returns to the previous operating mode. For faster
switching-over keep button MENU pressed until the
display shows the operating mode.

7.3 Adjusting the start address

To be able to operate the spotlight with a light controller,
adjust the DMX start address for the first DMX channel.
If e. g. address 17 on the DMX controller is provided for
controlling the red LEDs, adjust the start address 17 on
the PARL-7DMX. The other functions of the spotlight
are then automatically assigned to the following
addresses (in this example 18 to 20). The address 21
could be used in this example as the next possible start
address for the following DMX-controlled unit.
1) Press button MENU (5) once until the display (3)
shows . Make sure that the next button is
pressed within 15 seconds, otherwise the adjusting
process will end.
2) Press button ENTER. The adjusted address is
shown. For automatic adjustment of the address,
continue with step 4.
3) For manual adjustment, use button DOWN or UP
to adjust the address and memorize it with button
ENTER. reappears on the display. After 15 sec-
onds the spotlight returns to the previous operating
mode. For faster switching-over keep button MENU
pressed until the display shows the operating mode.
4) For automatic address adjustment of several
PARL-7DMX, firstly adjust the address of the first
unit manually ( step 3). At the following units use
button DOWN or UP to switch to
ing the function
start addresses will be adjusted automatically at
intervals of four.
Once the control signals of the DMX controller are
received, the red LED DMX (4) lights up and the dis-
play shows the start address. The PARL-7DMX can
now be operated with the DMX controller.

7.4 Control with the LED-4C

The unit LED-4C from "img Stage Line" is an easy-to-
operate control panel which can also be used for the
spotlight PARL-7DMX. It has 4 channels so that all
PARL-7DMX units connected to it can only be con-
trolled in sync.
1) Connect the jack DMX OUTPUT of the LED-4C to
the jack DMX INPUT (10) and switch on the LED-4C.
2) Adjust the start address of the spotlights to 1 or a
multiple of 4 + 1 (5, 9, 13, ... max. 61),
3) To control the PARL-7DMX with the LED-4C, the
DMX mode must be switched on:
a) Press button MENU (5) so many times until the
display (3) shows
button is pressed within 15 seconds, otherwise
the adjusting process will end.
b) Press button ENTER, the adjusted mode will be
shown ( ...
. After select-
, press button ENTER. The
chap. 7.3.
. Make sure that the next
).
c) With button DOWN or UP switch to the mode
and memorize it with button ENTER.
reappears on the display. After 15 seconds
the spotlight is switched to the modified operat-
ing mode, the display shows
and a number (1 – 16). The red LED SLAVE (6)
lights up.
Please refer to the instructions for the LED-4C for
more information about the operation.

8 Further Functions

8.1 Indication of temperature

To indicate the temperature inside the unit:
1) Press button MENU (5) so many times until
(temperature) is shown on the display (3).
2) Press button ENTER, the temperature (°C) is shown.
3) After 15 seconds the unit is switched back to the
previous operating mode.

8.2 White balance /colour balance

The balance between the three primary colours may
be shifted. This also changes the light colour of white
light. Thus, e. g. differences compared to other spot-
lights may be balanced when the LED spotlight is con-
trolled together with them.
1) Press the button MENU (5) until the display shows
.
2) Activate the menu item with the button ENTER. The
display now shows
3) Use the button DOWN or UP to switch to
the colour green and to
and then back to
first colour to be adjusted.
4) Press the button ENTER so that the correction
value (125 to 255) of the selected colour appears
on the display. Adjust the value for the colour with
the button DOWN or UP and confirm with the button
ENTER.
5) Repeat the steps 3 and 4 when the correction of
another colour is required.
6) If no button has been actuated for 15 seconds, the
unit switches back to the previous operating mode.

8.3 Display of the operating hours

To show the state of the operating hour counter:
1) Press button MENU (5) so many times until
(fixture hours) is shown on the display (3).
2) Press button ENTER, the operating hours are
shown.
3) After 15 seconds the unit is switched back to the
previous operating mode.
(= slave mode)
(red).
for the colour blue
for the colour red. Select the
GB
for
17