Triton TGEOS Instrucciones De Uso página 7

Anticlockwise (left) switch position
Clockwise (right) switch position
Note: To determine the sanding mode the sander is currently set to, disconnect the tool from the power supply, and attempt to turn the Hook and Loop Backing Pad (2) by hand. If the pad is hard to
turn and moves on an eccentric orbit, Forced rotation mode is selected. If the base turns easily around its axis, the sander is set to Free-run mode.
Operation
WARNING: Always use adequate protective equipment, including eye protection,
respiratory and hearing protection, when working with this tool.
WARNING: DO NOT touch the moving sanding disc.
WARNING: NEVER allow the sanding disc to completely wear down before replacing it.
Failure to observe these precautionary measures can lead to damage to the hook and loop
surfaces, resulting in sanding discs failing to attach properly.
Note: Always use clamps to secure your workpiece to the workbench wherever possible.
Switching on and off
WARNING: DO NOT switch the tool on or off whilst under load, as this will greatly decrease the
service life of the On/Off Sliding Switch (7).
1. Connect the plug to the power supply
Note: The Power Indicator (11) will illuminate when the machine is connected to mains power.
2. Hold the tool securely with both hands, one on the Main Handle (8), the other on the Front
Grip (3) or Auxiliary Handle (5), and make sure that you have full control at all times
3. Ensure the tool is not in contact with the workpiece before commencing with switching on
4. Push the On/Off Sliding Switch (7) forward until it engages, to start the machine
5. Push down on to the bottom of the On/Off Sliding Switch, to disengage the switch and
stop the machine
WARNING: Lift the machine off the workpiece before switching off.
WARNING: Always wait until the machine has stopped vibrating completely before putting it
down. Always disconnect from the power supply after use.
Adjusting tool speed
• This Triton sander features variable speed control that enables it to be used with a variety
accessories, to work on a multitude of different materials, workpieces and objects
WARNING: Never fit any accessories to the Hook and Loop Backing Pad (2) that are not
rated to the maximum no load speed of this device (see 'Specification').
1. Slide the Speed Control Dial (12) downwards on to a higher number, to increase the tool
speed
2. Slide the Speed Control Dial upwards on to a lower number, to decrease the tool speed
Note: This Triton sander features an electronic speed controller that holds the selected speed
constant under load.
• If in doubt about the correct speed setting, suitable for the task at hand, start with a low
speed, examine the results, and adjust to a higher setting if necessary.
Sanding tips
• Clamp workpieces to the workbench wherever possible. Ensure that workpieces cannot
move during work
• If the tool is connected to a vacuum dust extraction system, switch the extraction device
on before switching on the sander. Switch the sander off first, then the vacuum system
• Move the machine in a circular motion over the workpiece surface, applying an even,
moderate pressure until you reach the desired surface finish
WARNING: Excessive pressure does not lead to a faster removal of material; it will however
lead to premature wear of the sanding disc, and may cause damage to the machine. Both
sanding performance and quality depend mainly on the choice of the correct sanding discs.
• If there are still scratches on your workpiece after sanding, refer to 'Selecting the right
grade of sanding disc'
Free-run mode
Fine sanding with low material removal
This operating mode is recommended for handling sensitive
surfaces as well as for fine polishing. As a result of the free
running backing pad, an application pressure dependent
rotational movement at constant eccentric motion is
achieved. By varying the application pressure, the material
removal can be regulated slightly.
Forced rotation mode
Coarse sanding with high material removal & buffing
This operating mode achieves highest material removal
and is recommended for working very rough, insensitive
surfaces. This mode is also recommended for buffing. As
a result of the forced rotation, the backing pad constantly
moves on an eccentric orbit, whilst rotational around its axis.
Sanding metal
WARNING: Some additional precautions have to be taken when sanding metal.
• ALWAYS connect the sander via a suitable RCD
• ALWAYS connect the sander to a suitable workshop dust extraction system
• Clean the tool thoroughly before using it to sand metal
WARNING: Hot metal particles and sparks could ignite residual wood dust. Always clean
the tool THOROUGHLY when switching from sanding wood to sanding metal, and vice versa.
• A sanding disc that was previously used for sanding metal should not be used on wood
again. Residual metal particles may lead to scratches, and damage the workpiece surface
Accessories
• A range of accessories, including punched hook and loop sanding discs with various
grit, is available from your Triton stockist. For your own safety, use only genuine Triton
accessories. Spare parts can be purchased from your Triton dealer or online at www.
toolsparesonline.com
Maintenance
WARNING: Always disconnect from the power supply before carrying out any maintenance/
cleaning.
• This tool is manufactured using class leading components and makes use of the latest
in intelligent circuitry that protects the tool and its components. In normal use it should
provide a long working life
General inspection
• Regularly check that all the fixing screws are tight. They may vibrate loose over time
• Inspect the supply cord of the tool, prior to each use, for damage or wear. Repairs should
be carried out by an authorised Triton service centre. This advice also applies to extension
cords used with this tool
Lubrication
• Lubricate all moving parts with a suitable lubricant spray, at regular intervals
Cleaning
WARNING: ALWAYS wear protective equipment including eye protection and gloves when
cleaning this tool.
• Keep your tool clean at all times. Dirt and dust will cause internal parts to wear quickly,
and shorten the device's service life
• Clean the body of your machine with a soft brush, or dry cloth
• Never use caustic agents to clean plastic parts. If dry cleaning is not sufficient, a mild
detergent on a damp cloth is recommended
• Water must never come into contact with the tool
• Ensure the tool is thoroughly dry before using it
• If available, use clean, dry, compressed air to blow through the ventilation holes (where
applicable)
GB
7