Tabla de contenido
Idiomas disponibles
Idiomas disponibles
www.groupdynamics-laundry.com
cycle. Functions stay enabled permanently
until the user chooses to disable them.
The programming mode can be accessed
only with the door closed and with NON
coin-operated machines.
During programming, the cycle display reads
the selected cycle (1...9), whereas the time
display reads "Fy", where y is the option at
issue.
The temperature display shows the current
selection (0 = disabled, 1 = enabled; F3
envisages a third choice too -setting 2-: see
specific description).
A cycle is selected by pressing the SEL key,
whereas options are selected through the
PROG key and enabled or disabled through
the "+" and "-" keys respectively.
When the PROG key is pushed repeatedly,
options are shown in a cyclic sequence from F1
to Ci and then back to the current selection.
When the SEL key is pushed repeatedly, stored
cycles appear (minimum 1, maximum 9).
IMPORTANT !!!
When an option is selected for a cycle that
does not envisage it (see description of each
option) the machine will accept the selection
but the corresponding function will not be
carried out.
DESCRIPTION OF PROGRAMMABLE
FUNCTIONS
Enabling draining (F0)
As a rule, the tub is drained at the end of the
steps featuring water intake, in preparation
for the next step. The programming software
can overrun the draining step so that the
cycle may pass on to the next wash step with
water in the drum. This option is useful for
instance when heating in various stages or to
start the spin step with water in the drum and
drain during the speed-up. When this
parameter is set to "1", and the selected cycle
features it, this procedure is carried out.
Value
Function
0
Draining is performed always
1
Normal (default).
This function can be enabled for every single
cycle.
In standard programming, only the last rinse
step does not drain the water, so that the last
spin may be started with water in the tub,
which will be drained as soon as the machine
has distributed the wash load.
Cool-down (F1)
As a rule at the end of a high-temperature
wash cycle (above 60°C) soft water is taken
in in order for drum inside temperature to
decrease gradually. When F1 is set to 1, this
action is not performed.
Value
Function
0
Normal (default)
1
NO cool-down
This function can be programmed cycle by
cycle.
Shorter spinning (F2)
Final spinning can be set to 1 minute or
eliminated altogether. Effective spinning
means the maximum high-speed time. The
speeding up is not affected by this function.
Value
Function
0
Normal (default)
1
1 minute spinning
2
No spinning
This function can be programmed cycle by
cycle.
No prewash (F3)
When this function is enabled the prewash
step is excluded.
Value
Function
0
Normal (default)
1
No prewash
This function can be programmed cycle by
cycle.
Cycle deferred start (F4)
Postpones the start of a wash cycle and
determines cycle delay.
If the value assigned to this function is other
than zero, as soon as the programming session
is exited the time DISPLAY will blink the
hours and the temperature will blink the
minutes whereas the cycle display will read
the selected wash cycle.
To start the countdown, just press the START
push-button: the displays will be lit
continuously.
As soon as the countdown, is over the cycle
will start automatically and the displays will
resume their usual functions.
Before the START push-button is pressed
and during the count-down all keys are
enabled.
IMPORTANT !!!
Time is displayed in the "HH.MM"format.
H stands for hours and M for tens of minutes.
Unit: hours and minutes
Range: 00
h
00'...23
h
50'
(00.00...23.50)
Resolution: 10 minutes (0.1)
h
Default: 00
00'
Details:
When pressed, the START key excites the
CYCLE relay and the door is automatically
locked.
If the door is not closed correctly, the "door"
alarm will warn the user. If the door fails to
be locked, alarm "E6" will appear.
In this case the machine will not work until
the problem is solved and the START is
pressed once again.
If a deferred start is aborted - by entering the
programming mode and setting F4 to 00.00
- the door will be automatically unlocked.
Enable/Disable buzzer(F5)
This function enables/disables the buzzer,
which can be completely eliminated from all
cycles except for alarm sounds.
19
Value
Function
0
Normal (default)
1
No buzzer
Changes to this function will affect all cycles.
Changing heating temperature (F6)
This function lowers maintain temperature
by 10°C.
If a wash temperature in a cycle is normally
90°C, it can be set to 80°C by altering this
function.
Value
Function
0
Normal (default)
1
Temperature decrease by 10°C.
Changes to this function will affect all cycles.
Enabling drum rotation during take-in
and drain (F7)
When executing particularly delicate wash
diagrams it is appropriate to keep the drum
still while the machine is taking in or draining.
Value
Function
0
drum action enabled
1
no drum action during take-in/drain
This function is to be enabled for every
single cycle.
Caution! The drum still turns once
clockwise and once counterclockwise
before pausing and waiting for the
prescribed water level to be reached.
Adjustment of heating hystheresis (F8)
Setting this parameter it is possible to adjust
temperature precision at maintain steps. In
other terms, it is possible to determine when
the heating must go on again after the setting
was reached and then the temperature
dropped naturally.
The higher the precision, the more often
heaters go on and off.
Value
Function
2
the heaters get back on 2°C below
the temperature setting.
3
the heaters get back on 3°C below
the temperature setting.
4
4°C° below the temperature setting.
5
5°C° below the temperature setting.
6
6°C° below the temperature setting.
Assuming that this function is set to value 3
for a 60°C cycle, the machine will heat the
water up to 60°C and then the heaters go off:
the heaters will go back on only when the
temperature drops to 57°, and will stay on
until the 60°C setting is reached again.
Viewing the time to the end of the cycle (F9)
It is possible to decide whether the time read
is the effective duration of the selected wash
diagram or an absolutely arbitrary value that
can be set. Caution! This reading is
nonetheless a reference and does by no
means influence the effective duration or
the features of the wash diagram, whatever
Tabla de contenido
