DSC Power Serie Manual Del Usuario página 4

FCC COMPLIANCE STATEMENT
CAUTION: Changes or modifications not expressly approved by Dig-
ital Security Controls could void your authority to use this equipment.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interfer-
ence in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accord-
ance with the instructions, may cause harmful interference to radio com-
munications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful in-
terference to radio or television reception, which can be deter-mined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Re-orient the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an experienced radio/television technician for
help.
The user may find the following booklet prepared by the FCC useful:
"How to Identify and Resolve Radio/Television Interference Problems".
This booklet is available from the U.S. Government Printing Office,
Washington D.C. 20402, Stock # 004-000-00345-4.
The keypads represented in this manual can be used with the following
Control Units: PC1616, PC1832, PC1864.
IMPORTANT INFORMATION
This equipment complies with Part 68 of the FCC Rules and, if the
product was approved July 23, 2001 or later, the requirements adopted
by the ACTA. On the side of this equipment is a label that contains,
among other information, a product identifier. If requested, this number
must be provided to the Telephone Company.
PC1616 Product Identifier
PC1832 Product Identifier
PC1864 Product Identifier
USOC Jack: RJ-31X
Telephone Connection Requirements
A plug and jack used to connect this equipment to the premises wiring
and telephone network must comply with the applicable FCC Part 68
rules and requirements adopted by the ACTA. A compliant telephone
cord and modular plug is provided with this product. It is designed to
be connected to a compatible modular jack that is also compliant. See
installation instructions for details.
Ringer Equivalence Number (REN)
The REN is used to determine the number of devices that may be con-
nected to a telephone line. Excessive RENs on a telephone line may re-
sult in the devices not ringing in response to an incoming call. In most
but not all areas, the sum of RENs should not exceed five (5.0). To be
certain of the number of devices that may be connected to a line, as de-
termined by the total RENs, contact the local Telephone Company. For
products approved after July 23, 2001, the REN for this product is part
of the product identifier that has the format US: AAAEQ##TXXXX.
The digits represented by ## are the REN without a decimal point (e.g.,
03 is a REN of 0.3). For earlier products, the REN is separately shown
on the label.
Incidence of Harm
If this equipment (PC1616, PC1832, PC1864) causes harm to the tele-
phone network, the telephone company will notify you in advance that
temporary discontinuance of service may be required. But if advance no-
This product is in conformity with EMC Directive 89/336/EEC based on
results using harmonized standards in accordance with article 10(5),
R&TTE Directive 1999/5/EC based on following Annex III of the direc-
tive and LVD Directive 73/23/EEC as amended by 93/68/EEC based on
results using harmonized standards.
This product meets the requirements of Class II, Grade 2 equipment as per
EN 50131-1:2004 Standard. This product is suitable for use in systems
with the following notification options:
- A (use of two warning devices and internal dialer required),
- B (self powered warning device and internal dialer required),
- D (use of DSC model T-Link TL250 encrypted Ethernet communicator
required).
US: F53AL01BPC1614
US: F53AL01BPC1832
US: F53AL01BPC1864
tice is not practical, the Telephone Company will notify the customer as
soon as possible. Also, you will be advised of your right to file a com-
plaint with the FCC if you believe it is necessary.
Changes in Telephone Company Equipment or Facilities
The Telephone Company may make changes in its facilities, equipment,
operations or procedures that could affect the operation of the equipment.
If this happens the Telephone Company will provide advance notice in
order for you to make necessary modifications to maintain uninterrupted
service.
Equipment Maintenance Facility
If trouble is experienced with this equipment ( PC1616, PC1832,
PC1864) for repair or warranty information, contact the facility indicated
below. If the equipment is causing harm to the telephone network, the
Telephone Company may request that you disconnect the equipment un-
til the problem is solved. This equipment is of a type that is not intended
to be repaired by the end user.
DSC c/o APL Logistics 757 Douglas Hill Rd, Lithia Springs, GA
30122
Additional Information
Connection to party line service is subject to state tariffs. Contact the state
public utility commission, public service commission or corporation
commission for information.
Alarm dialing equipment must be able to seize the telephone line and
place a call in an emergency situation. It must be able to do this even if
other equipment (telephone, answering system, computer modem, etc.)
already has the telephone line in use. To do so, alarm dialing equipment
must be connected to a properly installed RJ-31X jack that is electrically
in series with and ahead of all other equipment attached to the same tele-
phone line. Proper installation is depicted in the figure below. If you have
any questions concerning these instructions, you should consult your tel-
ephone company or a qualified installer about installing the RJ-31X jack
and alarm dialing equipment for you.
Customer Premises Equipment and Wiring
Network
Service
Provider's
RJ-31X
Facilities
Jack
Alarm Dialing
Telephone
Line
Network
Demarcation
Telephone
Point
Answering
System
INDUSTRY CANADA STATEMENT
NOTICE: This Equipment meets the applicable Industry Canada Termi-
nal Equipment Technical Specifications. This is confirmed by the regis-
tration number. The abbreviation, IC, before the registration number
signifies that registration was performed based on a Declaration of Con-
formity indicating that Industry Canada technical specifications were met.
It does not imply that that Industry Canada approved the equipment
NOTICE: The Ringer Equivalence Number (REN) for this terminal
equipment is 0.1. The REN assigned to each terminal equipment provides
an indication of the maximum number of terminals allowed to be connect-
ed to a telephone interface. The termination on an interface may consist of
any combination of devices subject only to the requirement that the sum
of the Ringer Equivalence Numbers of all devices does not exceed 5.
PC1864 Registration numberIC: 160A-PC1864
PC1832 Registration numberIC: 160A-PC1832
PC1616 Registration numberIC: 160A-PC1614
Computer
Unused
RJ-11 Jack
Equipment
Unused
Fax Machine
RJ-11 Jack
Telephone
Telephone