Idiomas disponibles
Idiomas disponibles
Example of programming:
A.1.
1 2 3 4 5 6
A.2.
#/Reset
A.3.
9 7 6 1 0 8 0 8 8 C
A.4.
9 7 6 1 0 8 0 8 8
B. Emergency code:
Every safe has been programmed with an exclusive emergency code. We recommend you not to change it. If
you wish to change it, please, follow carefully the next sequence:
B.1. Open the door using the emergency code.
B.2. Press the key "#/Reset" (Fig. 2); the red light will turn on and a programming tone will be heard.
B.3. Press the key "3".
B.4. Press the key "#/Reset" (Fig. 2); the red light will turn on and 3 short beeps will be heard.
B.5. Enter the new code (from 2 to 15 digits), followed by the key "C" (Fig 3). After this, you will hear again the
programming tone.
B.6. Finally, introduce again the new code, so as to confirm it. A programming tone will be heard, the green light
will turn on, indicating that the new code has been programmed, and it is now possible to lock the safe. If the
programmation was not correctly done, you will hear an error tone and you should start form step B.2.
B.7. Before closing the door, check the new code at least three times, following the opening instructions.
Example of programming the emergency code:
B.1.
9 8 7 6 5 7 4 3 2 1
B.2.
#/Reset
B.3.
3
B.4.
#/Reset
B.5.
9 7 6 1 0 8 0 8 8 C
B.6.
9 7 6 1 0 8 0 8 8
BEWARE!: If you omit steps B.3. and B.4., you will always modify the user code.
6. EMERGENCY OPENING
Your safe is provided with an envelope which contains:
6.1. One mechanic emergency key, which will allows you to open the safe in case of electronic anomaly,
discharged batteries, forgetting of the code number programmed, etc. To use it, introduce the emergency key in
the keylock. Turn the key and open the door.
6.2. One emergency code number to open your safe in case that you have forgotten your normal opening code
number. Enter your emergency code number as usual. The green light will turn on, showing that you can now
open your safe. For your security the emergency code should not be changed. If you need to, do as explained
in point 6.B.
VERY IMPORTANT: You have received the emergency key and/or emergency code for your safe in an envelope.
Do not ever keep this envelope or its components inside your safe.
6.3. External power supply, to open your safe in case the batteries are completely discharged. To use it, put an
alkaline 9V battery (6F-22 S type) against the two black dots in the keypad (Fig.4), watching out that the polarity is
correct. Then, while holding the 9V battery on the keypad, introduce your code number, and open your safe as
usual. Do not forget to replace all four batteries for new ones, as soon as you have opened your safe.
7. OPENING DELAY PROGRAMMATION
This function activates a delay which blocks the opening of the safe for 1 to 99 minutes after the user code has
been entered. The red light flashes during the delay time, and when it is over, a short beep will be heard, the
system unblocks and allows the opening of the safe for 5 seconds. To activate or disactivate this function, the
door must be in the open position.
a) To activate this function:
Enter the following secuence: "C 1 0". The red light will turn on and you will hear the programming tone.
Press key "5" (this indicates that the time delay function will activate when opening with user code). You will hear
the programming tone. Introduce the desired delay number of minutes, from 01 to 99 (always 2 digits). You will
hear again the programming tone.
3 minutes delay programming example:
1.
C 1 0
2.
5
3.
0 3
b) To desactivate this function: just program the delay with 0 minutes time. The sequence is:
1.
C 1 0
2.
5
3.
0 0
NOTE: In the enclosed envelope, you will find a sticker which indicates that the safe has a delayed opening
system. Even if you do not activate this function, we recommend you to stick it up to the door, to dissuade possible
robbers.
(current user code)
(press the key "#/Reset")
(introduce new code + key "C")
(repeat the new code)
(open with the emergency code)
(press the key "#/Reset)
(press the key "3")
(press the key "#/Reset)
(introduce new emergency code + key "C")
(repeat new emergency code)
(Enter the sequence "C 1 0")
(Enter number "5")
(Number of delay minutes: 3)
(Enter the sequence "C 1 0")
(Enter number "5")
(Number of delay minutes: 0)
