BTV 6 Serie Manual De Instrucciones página 3

Idiomas disponibles

Idiomas disponibles

1. TECHNICAL FEATURES
* Power supply: 6 Volts (4 batteries, type AA, R6 or equivalent). Look at the sell-by date on the batteries (Fig. 6).
* Alkaline batteries recommended.
* Variable lenght codes, from 2 to 15 digits.
* Automatic blocking system for 5 minutes when more than 5 consecutive incorrect codes are entered.
* Low batteries' warning system (you will hear some tones followed by the flashing red light when you press some
key) and inside easy access to replacement of batteries (the batteries' holder can be found in a compartment
inside the door).
* E-EPROM memory circuit, which stores data for more than 40 years, with no need to have it connected to the
batteries.
* More than 5.000 openings with new batteries. Replace the batteries every year for correct functioning.
* One user code plus one EMERGENCY CODE.
* EMERGENCY KEY provided.
* External power supply, to open your safe in case the batteries are completely discharged
* Time delay function in user's code: from 0 to 99 minutes time delay.
2. RECOMMENDATIONS
Read carefully these instructions and warranty before any action.
Keep the identification number plate on the safe, this will allow emergency opening services, delivery of
spare parts and components, etc..
These safes should not be built in the floor; for this use, we recommend our wide range of floor safes. If
you install the safe in the wall, make sure that it is protected against humidity.
Watch out carefully for the expiration date of the batteries before installing them in your safe (Fig. 5 and 6).
The batteries included are only for transport purposes, we suggest that you change them.
Check and replace the batteries every year.
Do not install in a humid environment.
IMPORTANT! Check every action with open door, before closing it.
3. FIRST USE
3.1. If your safe is closed, open it with the emergency key you will find in the enclosed envelope (point 7).
3.2. If you find some drawback such as celofan, cardboard... next to the bolts, please remove it.
3.3. Next, fit the four batteries as indicated on point 9 of this instruction manual.
3.4. Then open and close the safe several times (point 5).
3.5. Change the original user code for your own one (point 6).
IMPORTANT! Check all those points with the door open, before closing it.
4. OPENING/CLOSING INSTRUCTIONS
Introduce the key and follow the next steps:
4.1. Introduce your code number (Fig. 1). All the safes have the code 1 2 3 4 5 6 programmed when used for the
first time. After you press each digit, there will be a short beep and the red light will turn on. If you do not press
any key for 7 consecutive seconds, the unit will disconnect; in this was the case, start again from the beginning.
4.2. If the code entered was correct, the green light will turn on and you will then have 5 seconds to turn the key,
while this light stays on. If the light turns off and you did not open the safe yet, go back to step 5.1. If the code
number that you have entered is not the one programmed before, you will hear a special tone indicating that this
code is not correct. If incorrect code numbers are entered more than 5 times consecutively, some long beebs will
be heard and the safe will stay locked for 5 minutes. During this time, the red light will be flashing and it will be
impossible to open the safe. When the 5 minutes have gone by, you will be able to open the safe as usual.
4.3. Turn the key to close the door.
IMPORTANT! Do not ever leave the key in the keyhole when you have finished using the safe.
5. PROGRAMMING OR CHANGING YOUR CODE
A. User code
Every safe has been programmed with the same user code. For your security do not forget to change it.
A.1. Open your safe following the instructions for opening (point 5).
A.2. Press the key "#/Reset" (Fig. 2); the red light will turn on and a programming tone will be heard.
A.3. Enter the new code (from 2 to 15 digits), followed by the key "C" (Fig. 3). After this, you will hear again the
programming tone.
A.4. Finally, introduce again the new code, so as to confirm it. A programming tone will be heard, the green light
will turn on, indicating that the new code has been programmed, and it is now possible to lock the safe. If the
programmation was not corretly done, you will hear the error tone and you should start from step A.2.
A.5. Before closing the door, check the new code at least three times, following the opening instructions.
OPERATING INSTRUCTIONS. SERIES 6 Y 900
loading

Este manual también es adecuado para:

900 serie