Making And Receiving Calls Using The Headset; Resetting The Digital Security Code - Sony SPP-N1003 Manual De Instrucciones

Making and receiving calls using the
headset
When the supplied headset is connected to the I (HEADSET) jack, you can talk
through the headset. The supplied headset is for use with the left ear. If the
headset does not fit comfortably to your ear or you would prefer to use a headset with
your right ear, please purchase a headset which is sold separately.
1
Connect the headset cord to the I (HEADSET) jack on the handset.
2
Wear the neckband around the back of your head. The cord should be
hanging from the left side.
3
Put your left ear between the earpad and the neckband, and adjust the
angle of the neckband to fit the headphones on your left ear.
Open the belt clip of handset by pressing the top of it, and then attach
the handset to the belt.
4
Position the headset microphone in front of your mouth.
1
I (HEADSET)
jack
3, 4
Precaution
Avoid listening your headset at so loud a volume that extended play might affect your
hearing.
Reattaching the belt clip
The belt clip will detach from the handset if more than 7
kilograms of continuous force is applied. In such a case,
refer to the illustration and reattach the belt clip.
2

Resetting the digital security code

The first time you charge the battery pack, a random security code is automatically
assigned between the base unit and the handset. Only a handset which has this
security code can make calls through the base unit. This system prevents the
possibility of other cordless telephone handsets making calls through your base unit.
You normally do not need to reset the security code. However, in the unlikely event
that you suspect that another cordless phone uses the same security code, you can
manually change the code. Pick up the handset from the base unit, and proceed as
follows:
TALK/BATT
LOW lamp
1, 4
2
Note
If the battery pack in the handset is completely discharged, or is removed from the handset for
more than several seconds, the digital security code stored will be lost. If this happens, charge the
battery pack and a new security code will be automatically assigned.
Tip
This procedure will change the code in both the base unit and the handset. The code can be
changed as often as desired.
Maintenance
• Clean the cabinets with a soft cloth slightly moistened with water or a mild
detergent solution. Do not use any type of abrasive pad, scouring powder or
solvent such as alcohol or benzine as they may damage the finish of the cabinet.
• If the charge terminals of the base unit and handset are soiled, wipe them with a
soft cloth.
If you have any questions or problems concerning your phone, please consult your
nearest Sony dealer.
Notes on power sources
On battery pack
• Store the battery pack at a temperature between 41°F (5°C) and 95°F (35°C) for
best performance.
• If you do not use the cordless handset for a long period of time, remove the battery
pack.
On power failure
• During a power interruption, you cannot make or receive calls.
For the customers in the USA
RECYCLING NICKEL-CADMIUM BATTERIES
Nickel-Cadmium batteries are recyclable. You can help preserve our
environment by returning your unwanted batteries to your nearest
point for collection, recycling or proper disposal.
Note: In some areas the disposal of nickel-cadmium batteries in
household or business trash may be prohibited.
RBRC (Rechargeable Battery Recycling Corporation) advises you
about spent battery collection by the following phone number.
Call toll free number: 1-800-822-8837 (United States and
Canada only)
Caution: Do not handle damaged or leaking nickel-cadmium batteries.
1
Press (PGM).
The TALK/BATT LOW lamp
flashes.
2
Press (#).
You hear a confirmation beep.
The dialing keys light up.
3
Press three of the dialing keys
(001 to 999) to store a new code.
4
Press (PGM).
You hear a long confirmation
beep and the TALK/BATT LOW
lamp goes off.
5
Immediately replace the handset
on the base unit.
You hear a long confirmation
beep and the phone stores the
new code.