Milwaukee 6310-20 Manual Del Operador página 4

1. Maintain labels and nameplates. These carry important information. If unreadable or missing, contact a MILWAUKEE service facility for a free
replacement.
2. DANGER! Keep hands away from cutting area and blade. Keep your second hand on auxiliary handle or motor housing. If both
hands are holding the saw, they cannot be cut by the blade.
Keep your body positioned to either side of the saw blade, but not in line with the saw blade. KICKBACK could cause the saw to jump
backwards (See "Causes and Operator Prevention of KICKBACK" below).
Do not reach underneath the work. The guard can not protect you from the blade below the work.
3. Check lower guard for proper closing before each use. Do not operate saw if lower guard does not move freely and close
instantly. Never clamp or tie the lower guard into the open position. If saw is accidentally dropped, lower guard may be bent. Raise the
lower guard with the lower guard lever and make sure it moves freely and does not touch the blade or any other part, in all angles and depths of
cut.
4. Check the operation and condition of the lower guard spring. If the guard and the spring are not operating properly, they must
be serviced before use. Lower guard may operate sluggishly due to damaged parts, gummy deposits, or a buildup of debris.
5. Lower guard should be retracted manually only for special cuts such as "Pocket Cuts" and "Compound Cuts". Raise lower
guard by lower guard lever. As soon as blade enters the material, lower guard must be released. For all other sawing, the lower
guard should operate automatically.
6. Always observe that the lower guard is covering the blade before placing saw down on bench or floor. An unprotected, coasting
blade will cause the saw to walk backwards, cutting whatever is in its path. Be aware of the time it takes for the blade to stop after switch is
released.
7. NEVER hold piece being cut in your hands or across your leg. It is important to support the work properly to minimize body exposure, blade
binding, or loss of control.
8. Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its
own cord. Contact with a "live" wire will also make exposed metal parts of the tool "live" and shock the operator.
9. When ripping always use a rip fence or straight edge guide. This improves the accuracy of cut and reduces the chance for blade binding.
10. Always use blades with correct size and shape (diamond vs. round) arbor holes. Blades that do not match the mounting hardware of
the saw will run eccentrically, causing loss of control.
11. Never use damaged or incorrect blade washers or bolts. The blade washers and bolts were specially designed for your saw, for optimum
performance and safety of operation.
12. WARNING! Use of this tool can generate dust containing chemicals known to cause cancer, birth defects or other reproductive harm. Use
appropriate respiratory protection.
13. Causes and Operator Prevention of KICKBACK:
KICKBACK is a sudden reaction to a pinched, bound or misaligned saw blade, causing an uncontrolled saw to lift up and out of the workpiece
toward the operator.
When the blade is pinched or bound tightly by the kerf closing down, the blade stalls and the motor reaction drives the unit rapidly back toward
the operator.
If the blade becomes twisted or misaligned in the cut, the teeth at the back edge of the blade can dig into the top surface of the wood causing the
blade to climb out of the kerf and jump back toward operator.
KICKBACK is the result of tool misuse and/or incorrect operating procedures or conditions and can be avoided by taking proper precautions as
given below:
14. Maintain a firm grip with both hands on the saw and position your body and arm to allow you to resist KICKBACK forces.
KICKBACK forces can be controlled by the operator, if proper precautions are taken.
15. When blade is binding, or when interrupting a cut for any reason, release the trigger and hold the saw motionless in the
material until the blade comes to a complete stop. Never attempt to remove the saw from the work or pull the saw backward
while the blade is in motion or KICKBACK may occur. Investigate and take corrective actions to eliminate the cause of blade binding.
16. When restarting a saw in the workpiece, center the saw blade in the kerf and check that saw teeth are not engaged into the
material. If saw blade is binding, it may walk up or KICKBACK from the workpiece as the saw is restarted.
17. Support large panels to minimize the risk of blade pinching and KICKBACK. Large panels tend to sag under their own weight. Supports
must be placed under the panel on both sides, near the line of cut and near the edge of the panel.
18. Do not use dull or damaged blade. Unsharpened or improperly set blades produce narrow kerf causing excessive friction, blade binding and
KICKBACK.
19. Blade depth and bevel adjusting locking levers must be tight and secure before making cut. If blade adjustment shifts while cutting,
it may cause binding and KICKBACK.
20. Use extra caution when making a "Pocket Cut" into existing walls or other blind areas. The protruding blade may cut objects that can
cause KICKBACK.
page 4
SPECIFIC SAFETY RULES — CIRCULAR SAWS